About the Kenwood Excelon KFC-XW1041
Big sound for a small price
Big sound for a small price
Whatever kind of music you prefer, a solid subwoofer gives you the bass response you need to bring your music to life. Kenwood's Excelon subwoofers are known for rugged construction and tight, punchy sound, and their KFC-XW1041 10" sub brings you the boom you're looking for at a surprisingly reasonable price.
Built tough, plays rough
The KFC-XW1041 sub features a two-piece polypropylene cone with Kenwood's X-Motif design and patterned surface for added rigidity, so you'll get maximum performance with minimal distortion. The sub handles up to 300 watts RMS and works in sealed or ported enclosures as small as 0.65 cubic feet. The CA-101G steel-mesh grille (sold separately) protects your speaker from accidental damage. When you're looking for the impact you need for all kinds of music, this sub is ready to rock.
Product highlights:
- 10" 4-ohm component subwoofer
- 2-piece polypropylene cone with rubber surround
- grille sold separately
- power handling: 300 watts RMS (1300 watts peak)
- frequency response: 33-300 Hz
- mounting depth: 4-7/8"
- sealed box volume: 0.65 cubic feet
- ported box volume: 0.9 cubic feet
- warranty: 2 years
- Our 60-day money-back guarantee
- MFR # KFC-XW1041
What's in the box:
Kenwood Excelon KFC-XW1041 owner's manual
- One 10" Subwoofer
- Trim ring
- Connection guide
- Template on box lid
- Specs printed on the box
Featured review
Good looking sub. Hits hard even though I'm currently under-driving it by about 100w. Fits well in the trunk of my eight six with a sound ordnance sealed box.
Dan from Missouri
10 reasons to shop with us
#10
60-day price protection
If our price drops after you buy, call us.
REVIEWS
Customer reviews
Loading reviews...
Kenwood Excelon KFC-XW1041 reviews
Average review:
Customer photos
More details on the Kenwood Excelon KFC-XW1041
Features & specs
| Size | 10 -inch | |
| Impedance | 4 ohms | |
| Cone Material | Polypropylene over Paper | |
| Surround Material | Urethane | |
| Ideal Sealed Box Volume (cubic feet) | 0.65 | |
| Ideal Ported Box Volume (cubic feet) | 0.9 | |
| Port diameter (inches) | N/A | |
| Port length (inches) | N/A | |
| Free-Air | No | |
| Dual Voice Coil | No | |
| Sensitivity |
84 dB at 1 watt | |
| Frequency Response | 33 - 300 Hz | |
| Max RMS Power Handling | 300 | |
| Peak Power Handling (Watts) | 1300 | |
| Top Mount Depth (inches) | 4 15/16 | |
| Bottom Mount Depth (inches) | N/A | |
| Cutout Diameter or Length (inches) | 9 | |
| Vas (liters) | 31.9 | |
| Fs (Hz) | 33.7 | |
| Qts | 0.513 | |
| Xmax (millimeters) | 5.9 | |
| Parts Warranty | 2 Years | |
| Labor Warranty | 2 Years | |
Product Research
Features
Sealed Enclosure Applications: Kenwood recommends a sealed enclosure volume of 0.65 ft³ (0.4 ft³ to 1.2 ft³ acceptable). Sealed enclosures provide the most control over a woofer, will handle a lot of power, and provide accurate sonic reproduction, making them suitable for all types of music.
Ported Enclosure Applications: Kenwood recommends a ported enclosure volume of 0.9 ft³ (0.7 ft³ to 1.2 ft³ acceptable) with a 10¾" wide x 1⅛" tall x 25½" long slot port. Ported (or vented) enclosures typically provide better overall efficiency than sealed, so they are suitable for use with smaller amplifiers, giving you more bass output from a given amount of power. However, this efficiency comes at the expense of very low frequency output.
Spring Terminals: The spring post terminals will accept pin connectors, single banana plugs, or bare wire up to 10-gauge.
Additional Measurements: When mounted without the trim ring, the sub has these measurements:
- Mounting Height: 0.428"
- Flange Height: 0.2"
- Frame Diameter: 10.563"
Warranty Note: Although the information included with these speakers indicates a 1-year warranty, they are actually covered by the Kenwood eXcelon 2-year warranty.
Loading accessories...
Customer Q&A
Loading articles...
