About the Axxess XSVI-9006-NAV Wiring Interface
Retain your vehicle's factory features with a new radio
Retain your vehicle's factory features with a new radio
You want to install a new car stereo in your Volkswagen, but you don't want to lose the useful features built into your factory radio. The Axxess XSVI-9006-NAV interface harness gives you the ability to connect your new radio to the existing wiring in your vehicle and keep your balance control, fader, and the Retained Accessory Power (RAP) feature. This harness also supplies the outputs you'll need if installing a DVD or navigation receiver.
This harness also includes a prewired harness for the ASWC-1 adapter (sold separately) which makes it much easier to keep your steering wheel controls. This interface is intended for non-amplified systems or when replacing a VW amplified system.
Product highlights:
- lets you replace the factory receiver and keep the balance and fade and Retained Accessory Power (RAP)
- for non-amplified systems or when replacing an amplified system
- plug-in harness for the ASWC-1 adapter
- warranty: 1 year
- MFR # XSVI-9006-NAV
What's in the box:
Axxess XSVI-9006-NAV Wiring Interface owner's manual
- Radio replacement interface
- Wiring harness
- Installation Instructions
Customer reviews for Axxess XSVI-9006-NAV Wiring Interface
Loading...
Loading reviews...
Average review:
4.0 out of 5 starsCustomer photos
This review was collected as part of a promotion
Pros:
Cons:
More details on the Axxess XSVI-9006-NAV Wiring Interface
Product Research
Features
Vehicle Compatibility: The Axxess Integrate XSVI-9006-NAV radio replacement interface module allows you to replace the factory radio in select 2015-up Volkswagen vehicles with an aftermarket head unit:
| Make | Model | Year |
|---|---|---|
| Volkswagen | Beetle | 2016-2019 |
| Golf | 2015-up | |
| Jetta | 2016-2018 | |
| Jetta GLI | 2016-2018 | |
| Passat | 2016-up | |
| Tiguan | 2016-2017 |
Amplified or Non-Amplified System Integration: The XSVI-9006-NAV interface supports non-amplified factor systems. You can also use it it amplified system, if you are planning to bypass the factory amplifier.
Retains Factory Backup Camera: The Axxess Integrate XSVI-9006-NAV radio replacement interface module provides a male composite video jack that plugs into the composite video camera input of your new aftemarket head unit, allowing you to retain your vehicle's factory backup camera.
+12V/10A Accessory Output: There is no 12-volt accessory wire in the factory harness, which requires the installer to run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio. The XSVI-9006-NAV is designed to provide a 12-volt, 10-amp switched accessory output (red wire).
Navigation Outputs: The XSVI-9006-NAV provides essential wires required for aftermarket radios that have navigation. VSS (Vehicle Speed Sense), Reverse, and Parking Brake wires are provided. This helps to cut down the installation time, since the installer does not have to look for these wires in the vehicle.
Retained Accessory Power (R.A.P.): The Retained Accessory Power (R.A.P.) function supplies power to the radio after the ignition is shut off until one of the front doors are opened. This function is retained by the XSVI-9006-NAV interface.
OEM Steering Wheel Control Compatible (optional): The XSVI-9006-NAV interface features a right-angle 3.5mm connector that lets you keep your vehicle's OEM steering wheel controls via the optional Axxess Steering Wheel Control Interface (120ASWC1, sold separately).
Loading...
Loading accessories...
Customer Q&A
7 questions already asked
Loading...
Loading articles...
Quick setup. The closure is a bit finicky and took a little patience to line up the harness but once in, good fit. Tons of extra wires so you just need to tuck everything towards the back and down to allow room.
Kirk from Port St Lucie, FL