Contact us
Close contact box

JL Audio HO112RG-W3v3

High Output Series ported enclosure with 12" subwoofer

Item # 13693136

JL Audio built their High Output Enclosures to give you a great combination of high sound quality and powerful output.

JL Audio built their High Output Enclosures to give you a great combination of high sound quality and powerful output.

Item # 13693136

Ships from distributor

Out of stock
C$699.99

About the JL Audio HO112RG-W3v3

JL Audio Built In USAPowerful output, bountiful bass

JL Audio built their High Output Enclosures to give you a great combination of high sound quality and powerful output. Engineers at JL Audio used a patented chamber-coupled port design to maximize bass production, and this unique enclosure is assembled by hand to exacting standards by the craftsmen at their Florida plant.

JL Audio Built In USA Powerful output, bountiful bass

JL Audio built their High Output Enclosures to give you a great combination of high sound quality and powerful output. Engineers at JL Audio used a patented chamber-coupled port design to maximize bass production, and this unique enclosure is assembled by hand to exacting standards by the craftsmen at their Florida plant.

Tough 12" sub

The HO112RG-W3v3 is built around the 12" W3v3 subwoofer, which uses its rigid polypropylene cone to push plenty of air for some serious bass output. Extensive venting helps prevent thermal breakdown in the voice coil, so you'll get lasting, consistent performance. The enclosure is wired for 2-ohm total impedance and will handle up to 500 watts RMS.

Patented ported enclosure

JL Audio makes this enclosure from CNC-cut, industrial-grade 5/8" medium density fiberboard, covered by thick gray carpeting (the baffle is covered in black carpeting), Three aluminum bars provide protection for the driver. The patented port design wraps around the enclosure and terminates at one side of the subwoofer, coupling the port to the sub's direct output. This speaker will function with as little as 150 watts, but performs best with 300-500 watts of power.

READ LESS

Product highlights:

  • 12" subwoofer in ported enclosure
  • 12" 12W3v3 speaker with dual 4-ohm voice coils
  • 5/8" medium density fiberboard sealed enclosure with carpet covering
  • patented chamber-coupled port design maximizes bass performance
  • maximum power handling: 500 watts RMS
  • 2-ohm total impedance
  • assembled in the U.S.A.
  • dimensions: 32-1/4"W x 15-1/4" H x 13-1/2"D1 x 7-1/2" D2
  • weight: 45-15/16 lbs.
  • warranty: 2 years (limited)
  • Our 60-day money-back guarantee
  • MFR # 93136

What's in the box:

  • HO112RG-W3v3 Ported subwoofer enclosure (loaded with one 12W3v3-2 subwoofer)
  • 3 Aluminum grille rods (installed)
  • Specification card
  • Warranty information

Customer reviews

Loading reviews...

JL Audio HO112RG-W3v3 reviews

Average review:

17 reviews

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

More details on the JL Audio HO112RG-W3v3

Pat M.

Features & specs

General
Woofer Size (inches) 12
Speakers Per Box 1
Woofer Material Mineral-filled Pol
Enclosure Type Ported
Color Gray/Black
Pieces in System 1
Width (inches) 32-1/4
Height (inches) 15-1/4
Depth (inches) 13-1/2
Second Depth (inches) 8-1/8
Connector Type 5-way post
Frequency Response 22-200 Hz
Power Range (Watts RMS) 500
Maximum Wattage Not Given
Sensitivity 87 dB
Impedance 2 ohms
Parts Warranty 2 Years
Labor Warranty 2 Years

Product Research

Features

Overview: This H.O. (High Output) subwoofer enclosure system is designed around JL Audio's W3v3-2 subwoofer. The H.O. enclosure is properly sized and tuned to the optimum ported alignment for the mounted 12" JL Audio W3v3 2Ω woofer.

H.O. Wedge Enclosure: JL Audio's patented High Output Enclosures feature a chamber-coupled port design to minimize turbulence and maintain excellent sound quality at all listening levels. The port wall integration and internal bracing ensure structural integrity. The slot-port wraps around the inner part of the enclosure and terminates beside the woofer. This type of design provides the necessary surface area and port length to maximize the performance of the JL Audio 12" W3v3-2. The enclosure's recessed mounting baffle and aluminum bar grilles also provide protection for the woofer. The enclosure has a pair of 5-way binding posts on the left side of the box.

Dimensions:

  • Width: 32-1/4"
  • Height: 15-1/4"
  • Depth:
    • At Base: 13-1/2"
    • At Top: 8-1/8"

12" W3v3 Woofer:

  • Dynamic Motor Analysis (DMA): DMA is JL Audio's proprietary method aimed at improving dynamic motor behavior. As a result of DMA optimization, W3v3 motors remain linear in motor force over a very long range of excursion, and also maintain a highly stable fixed magnetic field in the gap over a wide power range. The result is vastly reduced distortion, faithfully reproduced transients, and tight, clean, articulate bass.
  • Floating Cone Attachment Method (FCAM): JL Audio's patented FCAM technology is an innovative method of bonding the surround/cone assembly to the voice coil/spider assembly. This assembly technique ensures proper surround geometry in the assembled speaker for better excursion control and dynamic voice coil alignment.
  • Vented Reinforcement Collar (VRC): The Vented Reinforcement Collar is a composite structure that addresses two issues related to reliability. By reinforcing the critical junction between the cone, voice coil and spider, the VRC greatly reduces failures due to glue breakdown or material weaknesses. It does this by greatly increasing adhesive contact area and providing stress relief to the spider material at excursion extremes. the VRC also feature slots that facilitate air flow directly onto the voice coil windings to reduce thermal compression effects and enhances reliability.
  • Spider/Lead Wire Assembly: The W3v3 features a unique spider, coil and terminal subassembly which is assembled prior to installation in the speaker frame for optimum alignment and glue-joint integrity. The spider is insert-molded into a composite carrier tray which also incorporates the terminal assembly and lead wire strain relief features for enhanced reliability and optimal alignment of parts. The flying lead wires are carefully controlled and strain-relieved without resorting to woven-in lead wires, which can degrade spider performance.
  • Elevated Frame Cooling: The elevated frame design of the W3v3 delivers high-velocity air flow through slots directly above the top plate to the voice coil of the speaker. This not only enhances power handling, but also sound quality by minimizing dynamic parameter shifts and power compression.
  • Surround Stress Relief: By creating a radiused feature on the edge of the cone, stress is relieved from the surround material at maximum forward excursion, resulting in longer life and more consistent surround behavior.

Loading accessories...

Customer Q&A

Q
Crutchfield asked: Why did you buy this?
A
Cant afford to replace 10inch W6 with another, this seemed to be as close as I will get without spending a fortune. [ adam  Oct 07, 2018 ]
A
It's JL and at the price point you can't beat it. Hits hard. [ Dean  Mar 04, 2017 ]
A
various good reviews [ DAVID  Apr 25, 2016 ]

3 questions already asked

Q
Two different colors of carpet uploaded by customers. I prefer the dark, is that an option?
[ Joshua  Aug 10, 2019 ]
1 answer
A
As far as I know, that is not an option for this box. Only select models have black carpet but this one is grey and black carpet where the sub is. Sounds really good as well.
[ Aaron  Aug 10, 2019 ]
Q
I assume the grills are added to protect the woofer. Is it possible to also install an traditional grill for additional protection?
[ brett  Apr 08, 2018 ]
3 answers
A
It is possible, depending on the grill you would have to install it underneath the bars already set for they cannot be removed. They are definitely drilled into the wood
[ Matthew  Apr 09, 2018 ]
A
The woofer is set in pretty far away from the bars. Really doesn't need another gril but I would say you could get one in there if you really wanted to
[ John C.  Apr 08, 2018 ]
A
The bars feel like they can be pulled out so I assume that you can if you want. These bars are plenty in my opinion
[ Shawn  Apr 08, 2018 ]
Q
If the sub ever needs to be replaced, are the aluminum bars removable?
[ Barry  May 09, 2017 ]
1 answer
A
They are glued in you will need a heat gun to heat the glue up then they slide rite out.
[ Carl  May 09, 2017 ]

Loading articles...

TOP