Contact us
Close contact box

JL Audio XD1000/5v2

5-channel car amplifier — 75 watts x 4 at 4 ohms + 600 watts RMS x 1 at 2 ohms

Item # 13698258

JL Audio's XD1000/5v2 amp packs a wallop far beyond what you'd expect from something so small.

JL Audio's XD1000/5v2 amp packs a wallop far beyond what you'd expect from something so small.

Item # 13698258

Ships from distributor

In Stock
C$1,299.99
Add to wishlist

About the JL Audio XD1000/5v2

This one amp will power your entire system

JL Audio's XD1000/5v2 amp packs a wallop far beyond what you'd expect from something so small. This compact amp plays your music with true fidelity and impressive impact, without straining your car's electrical system. A cast alloy heatsink and an advanced cooling system keep this amp at optimal temperature, eliminating thermal shut-downs so your music keeps going strong without interruption.

This one amp will power your entire system

JL Audio XD1000/5v2

XD1000/5v2 connection and control panels

JL Audio's XD1000/5v2 amp packs a wallop far beyond what you'd expect from something so small. This compact amp plays your music with true fidelity and impressive impact, without straining your car's electrical system. A cast alloy heatsink and an advanced cooling system keep this amp at optimal temperature, eliminating thermal shut-downs so your music keeps going strong without interruption.

This 5-channel amp can power your vehicle's entire system, delivering 75 watts RMS to each of your front and rear speakers, while powering a sub with up to 600 watts. You can also switch to 3-channel mode, and power a pair of high-performance speakers with 200 watts each, while still driving a sub with 600 watts.

High- and low-pass filters give you intimate control over the character of your sound. "Differential-balanced" inputs keep the signals clear of outside noise, and allow you to connect this amp to just about any in-dash stereo, even a factory radio with no preamp outputs. An optional wired remote lets you tweak the level of the subwoofer or the whole system from your front seat.

JL Audio XD1000/8v2

XD1000/5v2 control panel

READ LESS

Product highlights:

  • 5-channel car amplifer
  • 75 watts RMS x 4 + 400 watts RMS x 1 (at 4 ohms)
  • 100 watts RMS x 4 + 600 watts RMS x 1 (at 2 ohms)
  • 200 watts RMS x 2 bridged at 4 ohms + 600 watts RMS x 1 at 2 ohms
  • variable high-pass filter (50-5000 Hz, 12 dB/octave) on ch 1 & 2
  • variable high-pass or bandpass filter (50-500 Hz, 12 dB/octave) on ch 3 & 4
  • variable low-pass filter (50-500 Hz, 12 or 24 dB/octave) on sub ch
  • optional wired remote for level control (sub channel only or all channels)
More details
  • Class D amplifier design with NextD™ switching amp technology
  • differential-balanced inputs eliminate noise coming from your vehicle's electrical system
  • speaker- and preamp-level inputs (speaker-level input requires an optional adapter)
  • auto turn-on via DC offset or signal sensing
  • Advanced Rollback Protection System prevents thermal shut-down
  • 4-gauge power and ground leads and a 80-amp fuse recommended — wiring and hardware not included with amplifier
  • no onboard fuses — when installing multiple amps in a system, an additional 80-amp in-line fuse between the distribution block and the amplifier is recommended
  • 14-3/4"W x 2"H x 7-1/8"D
  • warranty: 2 years
  • Our 60-day money-back guarantee
  • MFR # 98258
KEEP READINGREAD LESS

What's in the box:

  • 5-Channel Class-D amplifier
  • 2.5mm Allen wrench
  • JL Audio emblem
  • Owner's manual (English/ Spanish/ German/ French)

Customer reviews

Loading reviews...

JL Audio XD1000/5v2 reviews

Average review:

10 reviews

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Average at best and returned.

Crutchfield customer from Cypress, TX on 6/3/2019

Verified customer (What's this?)
Verified employee purchase (What's this?)

I purchased this product for my sons car. Lack of fullness in lower volumes and too much distortion in higher volumes. Paid restocking charge and piurchased HD. Much better.

Pros: Cost effective

Cons: You expect more for the money and brand.

Crutchfield response on

0 of 0 found this helpful

AMAZING????????

Crutchfield customer from Sheridan, WY on 3/19/2019

Verified customer (What's this?)
Verified employee purchase (What's this?)

AMAZING!!! Not only are their products the best but customer service for this business rocks!!! I highly recommend this company!!!!

Pros: Great product Best customer service for on line shopping

Cons: None

Crutchfield response on

0 of 0 found this helpful

Po

Crutchfield customer from Boise, ID on 1/31/2018

Verified customer (What's this?)
Verified employee purchase (What's this?)

Love this amp. More than enough power. I'm going to be upgrading the rest of the system soon. I'm very impressed with how clear JL products are. They are a little spendy but worth it. If ya want it to sound right the first time get all JL. It's all designed to work together. I am really impressed with this amp. I have this amp running a front set of JL components. The rear fill is just some infinity coaxials, I am running a single 12 W3v3-2 ohm sub for now. I am running this in a 2002 jeep grand Cherokee and it fills it. A sedan this would be probably extreme. I would go ahead and get another sub but I already had the box built for a single & I would need 4 ohm subs, right now I'm just running a singe 2 ohm. Once you hear a use this amp is going to make you want more.

Pros: Great amp for running a complete system. Great SQ & efficiency. Easy on the electrical system.

Cons: A little spendy.

Crutchfield response on

1 of 2 found this helpful

JUST AWESOME!!!!

Robert from Panama City, FL on 9/19/2016

Verified customer (What's this?)
Verified employee purchase (What's this?)

I have had other "system" amps that claimed to power all my speakers, and I was happy with the choice that was made for me in the past at other car audio installers , but my mind has been changed. The XD1000/5v2 is far and away the best performing full system amp that I have ever had! The power that it produces is clean and precise and makes my listening experience that much more awesome. The only negative thing that I can say is Im sorry I took so long to switch to JL. Not only do I have this amp but I also have the JL Audio HO112-W6v3 as well. This combination proves to be the best that I have ever heard!

Pros: compact size for the power output of the amp great sounding bass from the 12w6v3

Cons: NONE!!

Crutchfield response on

7 of 7 found this helpful

JL Audio XD1000/5v2

Miqueal from New Orleans, La on 5/22/2016

Verified customer (What's this?)
Verified employee purchase (What's this?)

Great amp. Pushing my Hertz door speakers & JL woofer to the limit

Pros: Remains cool to the touch after continuous use

Cons: Price

Crutchfield response on

9 of 10 found this helpful

F150

William B from mc lean, VA on 3/16/2016

Verified customer (What's this?)
Verified employee purchase (What's this?)

Awesome sound!!

Pros: Great sound to the speakers

Cons: Sub out is kinda weak

Crutchfield response on

1 of 2 found this helpful

Very impressed

Nathan from KS on 2/12/2016

Verified customer (What's this?)
Verified employee purchase (What's this?)

This amp fit cleanly under the passenger seat of my '16 Subaru. Unless you are just trying to annoy people this has more power than you'll need. It drives a single 10" Infinity sub, coax Alpine and Infinity Kappa components to the point you'll need hearing protection before it distorts. I'm interested in quality more than volume so this was my choice and I couldn't be happier.

Pros: compact size, plenty of power, easy connection, runs entire system with one small amp.

Cons: Does not sense speaker wire short. I don't know if that's regularly done but this thing puts out enough power to fuse and burn speaker wires without shutting down or overloading. Could potentially cause a fire in the right conditions; requires capable installation.

Crutchfield response on

8 of 10 found this helpful

JL Audio XD1000/5v2

Guest from ft lauderdale fl on 4/3/2015

Verified customer (What's this?)
Verified employee purchase (What's this?)

THIS AMP IS SMALL SLICK VERY CLEAN AND (((((((POWERFULLLLL)))))) HAVE IT RUNNING C5'650 N C2650X AND A HO12W6V3 WITH AN ALPINE HD149BT THIS SYSTEM SLAMS YET PLAYS VERY BEAUTIFUL THE HEART OF MY SYSTEM IS THIS XD1000/5V2 WOULD HIGHLY RECOMMEND IT *****

Pros:

Cons:

Crutchfield response on

10 of 11 found this helpful

Clean and powerful

Guest from AL on 9/13/2014

Verified customer (What's this?)
Verified employee purchase (What's this?)

Replaced two older amps with this single unit. Wasn't sure if this physically tiny amp was going to be able to provide the power I needed. No worries about that anymore. Clean, clear and able to play loud for as long as your ears can handle it. Powering a JL C5, JL C3 and two JL 10w3. Source unit is the factory Ford radio and the JL CleanSweep.

Pros: Small and powerful

Cons:

Crutchfield response on

14 of 15 found this helpful

Great Amp

Tim K. from California on 7/28/2014

Verified customer (What's this?)
Verified employee purchase (What's this?)

Great product. The amp has more than enough power to run my entire system, and it's small size made locating it very simple. This is my first time running JL Audio anything, and I have to say, their repuatation is well deserved.

Pros: Simple, Clean Setup. Small Footprint.

Cons:

Crutchfield response on

10 of 11 found this helpful

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

Product Research

Features
Controls
Connections

Features

5-Channel Amplifier: The JL Audio XD1000/5v2 is a five-channel, Class-D amplifier utilizing NexD ultra-high speed switching technology to deliver outstanding fidelity and efficiency. Four of the five channels are full range; two stereo pair, channels 1&2 and channels 3&4. The fifth channel is designed to power a subwoofer. The amp can be operated with a wide variety of source units and system configurations.

Specifications: The XD1000/5v2 is rated at 75 watts RMS x 4 plus 400 watts RMS x 1 at 14.4 volts, measured into 4Ω from 20 Hz to 20 kHz (for the full range channels) with no more than 1% THD+N. The four channel section is bridgeable to 200 watts RMS x 2-channels at 14.4 volts, measured into 4Ω from 20 Hz to 20 kHz with no more than 1% THD+N. Each pair of full range channels (1&2 and 3&4) is independently bridgeable, so the amp can be used in 5-channel, 4-channel, and 3-channel mode. The 2Ω output is 100 watts RMS x 4 plus 600 watts RMS x 1 at 14.4 volts, measured from 20 Hz to 20 kHz (for the full range channels) with no more than 1% THD+N. The subwoofer output is also given at 3Ω; 500 watts RMS x 1 at 14.4 volts with no more than 1% THD+N. The Signal to Noise ratio is 104 dB for the full range channels and 100 dB for the subwoofer channel at rated power, and 84 dB for the full range channels and 80 dB for the subwoofer channel at 1 watt.

NexD Class D Technology: NexD is a switching amplifier design that combines exceptional audio quality with excellent efficiency and less complexity. This results in an affordable compact amplifier with exceptional audio quality and total efficiency.

Advanced Rollback Protection: The XD-Series amplifiers employ advanced thermal and low-impedance protection to virtually eliminate annoying amplifier shut-down events. Should any XD-Series amplifier overheat, its intelligent, unregulated power supply reacts by limiting available peak voltage until the amplifier returns to a safe temperature range. Likewise, if an impedance lower than optimal for the amplifier is present at the outputs, the XD amplifier will roll back peak voltage to protect itself without shutting down.

Differential-Balanced Inputs: The amplifier features differential-balanced input architecture to effectively control noise and ensure compatibility with a wide variety of source units, including many OEM systems. Without resorting to line output converters, you can directly connect most OEM source units to the JL Audio amplifier without creating any noise or compatibility issues. Unlike conventional single-ended inputs, the differential-balanced design does not connect one side of the audio signal to chassis ground. This eliminates any voltage sensitivity between one input terminal and ground and greatly reduces the incidence of alternator whine in a typical car audio installation.

Note: You will need up to three speaker wire to RCA adaptors (136XDCLR2S, sold separately) to connect this amplifier to your headunit's speaker-level outputs.

Protection Circuitry with Status LED: There is a single multi-color LED on the top panel to indicate the amplifier's operating status.

  • Flashing Green: amplifier is powering up and audio output is muted
  • Constant Green: amplifier is turned on and operating normally
  • Constant Red: indicates the amplifier has exceeded its safe operating temperature, putting the amplifier into a self-protection mode which reduces the power output; the LED will return to green and the amplifier will resume normal, full-power operation when the heat sink temperature drops back to a safe level
  • Constant Amber (Yellow): indicates an over-current condition has occurred, accompanied by a muting of the affected amplifier channels (over-current can be caused by speaker impedance lower than recommended or a short-circuit in the speaker wiring)
  • LED Off: the only condition that will shut down an undamaged XD1000/5v2 completely is the battery voltage or remote turn-on voltage dropping below 10-volts

Cooling System: The outer shell of the JL Audio amplifier is designed to remove heat from the amplifier circuitry. For optimum cooling performance, this outer shell should be exposed to as large a volume of air as possible. Enclosing the amplifier in a small, poorly ventilated chamber can lead to excessive heat build-up and degraded performance.

Controls

Control Panel Cover: The XD1000/5v2 features a Control Panel Security Cover which protects and hides the amplifier's controls. When installed, the cover ensures that the amplifier's settings are not accidentally changed, while creating a clean aesthetic look for the amplifier and your installation. The cover is installed at the factory and must be temporarily removed for access the amplifier's controls. The security cover is secured by two 2.5mm Allen-head machine screws.

Gain Setting: The XD Series amplifiers have independent gain (input sensitivity) controls for each pair of output channels; in this case, 1&2, 3&4, and subwoofer. Using JL Audio's guided set up requires a digital AC voltmeter and a test CD (item number 503CD104, sold separately) with a sine-wave test-tone recorded at 0 dB reference level in the frequency range to be amplified for that set of channels (50 Hz for subwoofer channels, 1 kHz for a midrange application).

Input Voltage: The input voltage range is broken into two sub-ranges (the sub-range is set simultaneously for all inputs, but the three sections have independent gain controls to set the specific voltage):

  • Low: typically used with preamp level signals; variable from 200mV to 2V
  • High: used with some high output preamps and most speaker level signals; variable from 800mV to 8V

Remote Level Mode: When the optional HD-RLC wired remote is added, use this switch to set which channels are affected:

  • All: all channels are adjusted simultaneously
  • Sub: only the subwoofer channel is affected

Turn-On Mode: There are three options for turning the amp on, selected using the Turn-On Mode switch:

  • Remote: The amp turns on when +12 volts is applied to the remote terminal.
  • Offset: The amp turns on when a DC offset is detected on the channel 1 inputs (from a speaker-level source).
  • Signal: The amp turns on when a full-range audio signal is detected on the channel 1 input (from a speaker-level source).
Input Mode: Choose which inputs are used with this three position switch:
  • 6 CH: each of the six inputs feeds its corresponding output
  • 4 CH: inputs 1-4 feed output channels 1-4 respectively, and the subwoofer input is the sum of all four
  • 2 CH: input 1 feeds channels 1&3; input 2 feeds channels 2&4, the subwoofer input is the sum of both

Crossovers: Each section of the amplifier has an independent crossover:

  • Channels 1&2:
    • HP Filter Mode: three position switch:
      • Off: full range
      • x1: high-pass; crossover point is as labeled on the frequency dial
      • x10: high-pass; the crossover point is multiplied by 10, making the range 500 Hz to 5 kHz
    • Filter Frequency: rotary control; set the crossover point from 50 to 500 Hz (with the filter mode switch in the x1 position) or 500 Hz to 5 kHz (with the filter mode switch in the x10 position)
  • Channels 3&4:
    • Filter Mode: three position switch:
      • Off: full range
      • BP: band-pass; high-pass frequency set using the channel 3&4 filter frequency dial, low-pass frequency taken from the setting channel 1&2 filter frequency dial
      • HP: high-pass; frequency set using the filter frequency dial
    • Filter Frequency: rotary control; set the high-pass crossover point from 50 to 500 Hz
  • Subwoofer:
    • Filter Mode: three position switch:
      • Off: the crossover is bypassed; assuming a full range signal is input, the output will be the full range of the subwoofer amp section, which is 10 Hz to 1 kHz
      • 12 dB: the low-pass crossover slope is 12 dB/octave
      • 24 dB: the low-pass crossover slope is 24 dB/octave
    • Filter Frequency: rotary control; set the crossover point from 50 to 500 Hz

Connections

Power/Ground/Turn-On Terminals: The amplifier features screw clamp terminals for the power, ground, and remote turn-on connections.

  • Power and Ground: designed to accept 4 AWG wire; a A 2.5mm Allen wrench is supplied for making connections
  • Remote Turn-On: designed to accept 18 to 8 AWG wire; the same 2.5mm Allen wrench is used for making the connection

Note: The Amplifier is not equipped with a fuse. An external 80-amp fuse (not included) must be installed on the power wire. If a wiring kit is used which includes a fuse with a value other than 80-amps, the original should be replaced with an 80-amp fuse.

Speaker Output Terminals: The XD1000/5v2's screw clamp speaker terminals will accept 16 to 8 AWG speaker wire. The included 2.5mm Allen wrench is used for making connections.

Note: The two subwoofer outputs are internally wired in parallel, making it easy to connect two subwoofers (minimum impedance 4Ω each when using both).

Preamp Inputs: The amplifier has three pair of differential-balanced stereo RCA inputs; each pair has a dedicated gain control designed to match the input sensitivity of the amp to the specific signal source feeding it. In addition to preamp level signals, the RCA inputs are also used with speaker level signals (136XDCLR2S required and sold separately).

Remote Level Control: The amplifier features an RJ-14 telephone jack for adding an optional wired remote level control. With the addition of the optional wired remote (item number 136HDRLC, sold separately), you can control the volume of all channels of the XD1000/5v2, or just the subwoofer channel, from the front of your vehicle. This is useful for subwoofer level control or even as a master volume control for your system. If desired, multiple XD amplifiers can be controlled from a single HD-RLC controller using a simple phone line splitter and multiple phone cables (all sold separately).

Note: All inputs and outputs are located on one side of the amplifier to make installation simple and neat.

Loading accessories...

Customer Q&A

Q
Crutchfield asked: Why did you buy this?
A
Reputation [ Victor  Apr 05, 2017 ]
A
Recommended by Crutchfield support for my application. Wade was very helpful selecting the right amp for my setup. [ Hector  Dec 04, 2016 ]

4 questions already asked

Q
Is this amp 1ohm stable? I have 2 JL Tw3 10" subs (4ohm dvc) wired to it now in series @4ohm but would like to wire them parallel parallel down to 1ohm to increase the power to each. Will this amp handle it?
[ Cody  Jun 21, 2017 ]
2 answers
A
Hey Cody I'm afraid I have no idea. I suggest you contact JL Audio, or the crutchfield tech team. They will be able to answer your question, and give you the proper wiring sequence to handle the load, if possible. Sorry I wasn't able to help.
[ chris  Jun 22, 2017 ]
A
No. 2ohms is as low as you can go without potentially damaging your equipment.
[ Michael  Jun 22, 2017 ]
Q
Can this amp use a single input to provide signal to all 5 channels? (using the MBT-CRX as a source instead of a head unit)
[ A  Feb 02, 2017 ]
1 answer
A
Yes, for installations like that you can set the "Input Mode" switch on the front panel to "2-channel" which makes it so the audio source connected to the front/main RCA inputs is fed to all of the amplifier channels. If you would like to discuss further, feel free to contact an Advisor directly by phone (1-800-324-9695) or online chat. Hope that helps!
[ Larry  Feb 14, 2017 ]  Staff
Q
When I look at pictures of the amp, it appears that the subwoofer 'channel' is actually 2 channels. Does this indicate that it has to be bridged when wiring to a single sub? If so, is that taken into account with the claim "600W at 2 ohms" - is this implying a bridge and 2 ohm sub resistance? Is the amp stable under these conditions?
[ Donovan  Nov 29, 2015 ]
1 answer
A
there are two "+" positive connections and two "-" negative connections. This is to facilitate multiple subwoofer wiring. The two positive and two negative connections are connected in parallel inside the amplifier They are not stereo outputs.s. It is rated for 300W into 2 ohms, 250W into 3 ohms and 200W into 4 ohms (Continuous Power, RMS Method). i'm running a 10 jl @ 2 ohms and the amp does not heat up much
[ Darrell  Nov 30, 2015 ]
Q
I want to power four Rockford Fosgate speakers and subwoofer with the JL Audio XD1000/5v2. The amp produces 600 watts RMS at 2 ohms and the sub is a DVC which can handle 400 watts RMS at 2 ohms nominal impedance. Is it true that if I wire the voice coils in series this will step up the impedance to 4 ohms and essentially halve the power from 600 watts at 2 ohms to 300 watts at 4 ohms? If this is incorrect please suggest how this may work out... Thanks.
[ Brad  Nov 24, 2015 ]
1 answer
A
Close, correct for speaker theory amp practice gets more complex. power ratings from the amp specs on Crutchfield: Product Highlights: 5-channel car amplifer 75 watts RMS x 4 + 400 watts RMS x 1 (at 4 ohms) 100 watts RMS x 4 + 600 watts RMS x 1 (at 2 ohms) 200 watts RMS x 2 bridged at 4 ohms + 600 watts RMS x 1 at 2 ohms Voice coils in series also need to be in phase I hope your sub includes directions if not trial & error can get you there if you know that out of phase will cancel out and just generate heat, low power test always.
[ Alex  Nov 25, 2015 ]

Loading articles...

TOP