Will work with drilling

2008-2013 Forester/Impreza these will NOT be a direct fit. It will require one of the holes to be drilled into the sheet metal of the door. No instructions tell you this, other than to mention a drill may be needed. It WILL work, you can even use the same screws, but plan on drilling.

Have questions for
?

Fit as described for my car!

Brackets fit as described for my 2013 Kia Rio LX.

Have questions for
?

NICELY DONE

PERFECT FIT

Have questions for
?

Glad they were free with the speakers

Absolutely does not even remotely fit a 2008-2014 Impreza/wrx, the bracket itself is too small to reach the 3 mounting screw holes even with generous modifications. Also some speakers with wider mounting widths (like my morels) need the inside to be opened up as well. Pick up something that fits and save some headaches.

Have questions for
?

08-14 WRX hatch

Bracket worked fine. Screws that were included with ~4 inches long and entirely useless.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

This bracket was listed as fitting a 2012 Forester rear door, but only two of the three holes fit.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

The brackets need to be about a half inch deeper. There is a metal bar in the door that the speakers contact. I had to make spacers to make them work.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Bought for 2007 Sonata SE to replace a non-working stock woofer. I could re-use 2/3 mounting holes on each front door, but did have to drill 1 new hole on each side in the door and add a gap/hole for the wiring adapter. Not a big deal if you have a cordless drill and a little time. It works just fine once you're all done but the bracket itself has no instructions and does not come with mounting hardware to secure the bracket to the door, so had to make an extra trip to for some short screws and nuts - too long and they stop the window glass from sliding down fully. I used a $1.29 packet of short machine screws and nuts to get the bracket on the door, so not that bad compared to what I'd get charged to have someone do it for me. Overall good but don't expect a fully seamless experience, you'll probably have to do some drilling if you own a car like mine.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Great

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

2016 Kia Rio. Does not fit 6 3/4 speakers that well. Had to use bolts through the slots to make it work. If they tell you to clip the inner brackets off then you can't use the clips.

Have questions for
?

Perfect fit

Perfect fit for my 2013 Kia Rio

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Worked perfectly with the Rockford Fosgate R165X3 speakers for my 2010 Subaru Impreza. No issues with install or mounting.

Have questions for
?

Dis nit work well in my 2011 Forester.

Did not fit well in my 2011 Subaru Forester. I had to use them upside down and use some "fitness" to mount the speakers. Fr from "exact fit"

Have questions for
?

An "Alleged" fit - NOT.

I don't know why Crutchfield even lists these as a fit for my vehicle ('08 Subaru STI). The only thing that "fits" is - well nothing. The Mounting holes don't line up with the OEM holes in my doors. CF advisor did tell me that I'd have to drill holes - but again, it begs the question - WHY LIST IT AS A FIT FOR THE VEHICLE? I see other reviews here with the same issue. Scosche could easily make these with the right hole orientation for all the other vehicles - like mine - that don't use this particular hole alignment. We (Crutchfield advisor and I) discussed the mounting...but when I went to install: - even my speakers' holes didn't line up with ANY holes on the brackets...and these are standard 6.5" speakers with the standard four holes. - even if I broke off the inner tabs - designed for 5" speaker mounting I presume - my speakers STILL would not have fit into the primary hole. (HERTZ MPX 6.5s) - I considered drilling and modifying them...but as noted, this would not have worked well, if anything resulting in a substandard install. And obviously I couldn't return them once cut. This drives me nuts...the "pro advice" justifies Crutchfield's generally higher prices. I ended up making my own out of MDF and some glued speaker cabinet fabric to get a good seal on the doors. Ironically these home-made adapters fit perfectly on my other Subaru ('10 Legacy). Maybe I should start selling these...there are obviously many vehicles out there for which these would be a perfect fit

Have questions for
?

Almost worked without additional tinkering

The screws that came with didn't hold. Had to go to the hardware store and buy machine screws with nuts and countersink the nuts in the bracket by heating it with a torch

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

They were free with the speaker purchase so I can't complain but I had to Dremel the tabs off to get the speakers to fit. Even then, the brackets don't fit the doors well.

Have questions for
?

Just as described

These were a perfect fit for 08 Hyundai Sonata. The inner tabs snap off easy to accommodate the 6 1/2" speakers.

Have questions for
?

2014 GMC Terrain W/O pioneer system

They fit perfect on all four doors, but the only issue I had was that on my front doors the window elevators literally sit right behind the speaker holes and since these speaker mounts are much thinner than the factory mounts, my new speaker's magnet would sit on the elevator causing the speakers to not sound so great. So I left these new mounts on the rear doors since the window elevators were in a different position, but on the front ones I rigged the old OEM speakers and now they sound better. (Cheap speakers but I just wanted to replace the factory set because they were old and starting to tear apart)

Have questions for
?

Not a good fit for my door or my speakers

I am disappointed with Crutchfield and this product. Crutchfield makes it seem like they give you step by step instructions for this product and your specific vehicle. The instructions are barely useable, and not detailed at all. My car is a 2013 Hyundai Accent, and the checker said these mounting brackets fit my car and were suggested accessories for the 6 1/2 JVC speakers I purchased. I thought this would be an easy fit. I should have known when the sticker on the package states these mounting brackets are for Chevy Equinox/Saturn Vue doors, but I figured maybe it's a universal fit. None of the holes on the brackets match any holes in my car door. NOne of the holes on the bracket match the holes on my speakers, except if I mount the speaker to the thin tabs that are meant to break away for 6 3/4 speakers. There are no instructions, no screws, and no indication what size screws I would need to buy to install the brackets into my door panel (and no instructions as to what size holes I will now need to drill into the metal of my car door panel. Overall, very unhappy that I have to basically rig this up myself, with really nothing matching the way it is supposed to.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Perfect fit adapters made installation straight forward and easy.

Have questions for
?

Poor design

No hardware supplied, not many locations to attach speakers, thin mounting surface for speaker screws.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Perfect fit

Have questions for
?

Almost, but not quite

The adaptor fit the door panel beautifully. A person really couldn't ask for better. A pity though the speakers don't fit the adaptor. I spent hours reengineering a way to attach the speaker to the mount. I ended up having to drill out the "slots" that were provided to accept #8 screws, and then affix a form of Tinnerman nut run the screws into. Disappointing. Very disappointing. Oh, did I say disappointing? I'm sorry I didn't take any pictures, but by the time I finished this project I was in no mood to take another minute longer getting the door panel back on. Disappointing.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Worker to offset the aftermarket speakers in my subaru

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

easy to install

Have questions for
?

Great

Well worth the money to not make my own

Have questions for
?

Wrong item for vehicle

Did not fit or matched with the mounting locations of the vehicle. I believe this is the wrong item for my vehicle. Had to modify item to make it fit.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Helps installation to replace OEM speakers

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Perfect fit with no issues

Have questions for
?

Very satisfied!

Easy to install. Fit perfectly to replace factory speakers.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

One size does not fit all. Had to radically modify to get to fit Subaru and still not too happy with results

Have questions for
?

Almost great

2016 GMC Terrain: the spacing was appropriate but I had to drill to make the screws that came from Crutchfield work, as they were too long and contacted the door.

Have questions for
?

Terrible product details.

Bought these after I tried to install my new speakers which didn't fit, these didn't fit either, had to cut them myself and they still barely fit. Ticked at the fact that the page says it'll fit my car but once I get them they magically don't. Same thing for my speakers. When I initially bought the rockford fosgates, The page said the speakers were compatible with my car, ok cool, after they didn't fit I go back to look them up then all of sudden they page said they were not compatible. So I was ticked, but I figured with a mounting bracket I'd be fine, so I bought them, go to put on the bracket and its one screw off for the door and the speakers didn't fit, so for the speakers to fit I cut the inside of the brackets, so that worked, but now the speakers are holding on by two screws each. Bad part is that no wiring harness nor mounting brackets were recommended when I bought the speakers. I like the products but the compatibly of your products to vehicles needs to be more detailed and thoroughly looked into. I know this review won't make it to the page for other customers to view, I know how that pick and choose move works, which is really poor so whoever reads these. I'm not buying from you guys anymore. Been too much of a hassle for what it's worth.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

easy to use. Removable pins to fit your different style of speakers.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

The quality is there except only 2 of 3 holes lined up with the factory mounting holes.

Have questions for
?

Bad fit

These are garbage. These are the only brackets sold by crutchfield that fit my 2013 subaru wrx. At best 2 of the screws fit the pre drilled holes and the 3 "might" fit if the head of the screw catches the outside of the plastic. With the Pioneer speakers that I got, this bracket seats the positive and negative terminals to rest on the metal cutout from my door and GROUNDS OUT THE SPEAKER. Buy something else.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Did the job, but had to drill some extra screw holes in order to fit existing screw holes properly.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Didn't really match up with my girls 2014 Kia Sorento just had to cut out the old speaker and use the original speaker mounts!!! Not to hard to do and they were free so can't really complain!!

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

only thing I didn't like was when mounting speakers to the bracket, the bracket has slots so the screw wants to sideways.

Have questions for
?

Fits ok but not perfect

A screw boss for 6 1/2 speaker application uses a half circle boss, and these holes are not so robust. They strips easy, and I needed to find bigger screws. It would have been nicer if screws are included or appropriate screws are recommended.

Have questions for
?

Ok product.

Brackets are plastic and don't have enough surface for screws to thread into them securely. If not careful plastic will give and screw will not be able to tighten. They don't fully line up with my Polk Audi speakers. I managed to make them work.

Have questions for
?

Ok, but too shallow.

These seemed well made. unfortunately they were not deep enough to prevent the speaker magnet from coming into contact with the window track in the door. After further research I found that I actually needed Metra 82-3307, which Crutchfield doesn't carry. So these would work as long as you use speakers that are a shallower mount, which prevents you from really upgrading the stock speakers significantly.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

They work great.

Have questions for
?

Adapter

Fits perfect on the regulator. Well need to drill a hole but it will fit

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Had to drill holes due to not being made for the application I was using them for

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Perfect fit for my 12 Equinox!!! Thank you for including these in the purchase of my speakers!!!

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

adapter brackets were easy to install and performed as described

Have questions for
?

2011 STi

I have a 2011 STI, it wasn't a Cinderella shoe. But I made it work. Had to drill a hole, on the bottom left to make fit. They do the job. Better then anything else I've found

Have questions for
?

Works fine

Dunno what to say, they do what they are suppose to lol.

Have questions for
?

No inserts, no upgraded speakers

Couldn't have installed the speakers without these inserts. Worked great!

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

The adapters fit the holes, but the hardware is somewhat a mystery. The Crutchfield instructions refer to the mounting brackets instructions (none exist that I could find). So we had to scrounge up fasteners to fit. Better installation or fastener combination would be an improvement.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

I received these with my purchase of 6.5" speakers for a Kia Rio 2013 Hatchback. I wasn't impressed. The mount fit on the door, but the speakers didn't fit on the mount unless they were reversed. I ended up going old school and made my own MDF rings. After cutting out two matching 3/4" rings, glueing together, and painting to make sure they hold up under any potential moisture, I also used some non-hardening modelling clay to help build a load around the mount against the doors. In addition, I also cut the speaker ring off the door panel itself, and ended up using some thick furniture felt to reduce any potential vibrations against the MDF rings and plastic. Doing this, I could have gone with a 7" speaker easily even though the Crutchfield "specialists" indicated the 7" speakers wouldn't fit. Building up the 1.5" ring gave me that extra depth I needed. While I understand these mounting brackets are designed to be as universal as possible, they honestly sucked for the installation on the 2013 Kia Rio. At the end of the day I threw the rings in the trash where they belong.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Good product for mounting speakers in my 2011 Equinox

Have questions for
?

Good, but Metra 82-8900 is better for 2012 Forester rear door

I believe the product is well-designed and constructed of appropriate material to do a good job in the vehicles it fits. That being said, my 2012 Subaru Forester was not such a vehicle. Crutchfield sent it along for free with speakers, as they do, and noted an additional hole would need to be drilled to make it fit. Unfortunately, there is only one orientation where 2 of the 3 holes would line up and the place a new hole would need to be drilled was awkward and difficult, as it was on an angled surface and would require removal of a plastic part of the panel (the bit holding the original speaker hole). The good news is I had an extra pair of Metra 82-8900s and they fit the stock holes much better (not quite perfectly; one screw sits a little further from the overall center than would be ideal, but no additional holes are needed and they hold the bracket just fine).

Have questions for
?

Poorly Made - Screw holes too large

The brackets fit the existing location just fine, and I had no problems lining up holes for the speakers. The problem I had is that the screws that came with the bracket were too small for the holes in the plastic. I was able to get the screws just barely tight enough to stay in. Now after a few years, they are coming loose and the speakers are rattling in the doors.

Have questions for
?

throw them out

bought a whole speaker system from Crutchfield. the screw holes were terrible and did not hold any screws, i had to make my own good thing they were free i can see why...

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Used these adapters for a 2012 Chevy Equinox with the lowest model stereo system in the front door. They line up perfectly with the original mounting locations but the holes for the 6 1/2" speaker were slightly off. I was able to work around and get a tight fit but took some time to get perfect.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

The spacers were perfect. Kept the new pioneers close to factory specs.

Have questions for
?

Must have for some GM doors

fit the factory space great with no mods for my 2006 Saturn Vue. For one set of speakers no tabs to remove, the other set had to remove all the tabs but was easy. Beats having to custom fit a bracket. No way to mount any speaker directory to door since hole was larger than speaker basket.

Have questions for
?

Good product, bad recommendation (C'mon, Crutchfield)

Does not fit 2008 Subaru Impreza WRX. Make sure to read into each item the Crutchfield team recommends for your vehicle, as they are not always compatible.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Definitely does NOT nicely fit the rear door of a 2011 Impreza. Required a little finagling to work in the front doors, and major finagling to shoehorn them into the back doors. The screw holes do not line up, and there isnt enough extra plastic to make them wider to accommodate the factory screw locations. In forcing the misaligned screw holes, it tweaks the bracket slightly out of circular shape, making the speaker cage load-bearing. Probably not a huge problem, but the whole thing is under tension, which is not ideal. There has got to be a better solution for our Subarus.

Have questions for
?

Great Speaker bad brackets

These did not work at al for my 08 Impreza four door. They either didn't line up or they were too shallow. The screws included were the wrong length and came through the back side of the mount and were touching metal and grounding out my system. A job that should have taken 1.5 hours ended up taking 4 hours over two days and several trips to the hardware store.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Crutchfield recommends these for the GE/GR body WRX/STI but that is not even close to the case. New holes had to be drilled into the doors to mount these rings as they did not fit even close to the stock location. I would've done away with them if my magnets wouldn't have interfered with the window glass but that was the case without the rings. Luckily I have them mounted flush so they aren't rattling like others have complained about

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

They do not fit flush to the door, nor do the screw holes line up. I had to drill them to make them fit. There's now a rattle from not fitting flush against the door. They are not a direct fit as described.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Was not a very good aftermarket mount for my application had to be modified to make work

Have questions for
?

Holes aren't in the right place

Didn't fit in my 2011 Subaru Impreza, Only 2 holes lined up

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Great product.

Have questions for
?

Perfect fit

Bracket fits perfectly, so now the speakers do as well

Have questions for
?

Solid product not made for Subarus

So the construction of these are very solid. Unfortunately they do not fit a 2011 Subaru Impreza with a stock premium sound system. I attempted to join the mounts to the OEM speaker mounts. This made the speaker to proud to mount the door panel. I was hoping for a product that would be a direct bolt and go like the stereo head unit adapters. At least it was included in the speaker purchase and not extra.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

best purchase I ever made

Have questions for
?

Does NOT work with 2010 Subaru Forester

They the speakers mount to the adapter is bad. I had to use long screws and make holes in my Forester to solidly mount the speakers. This is NOT an EXACT fit for the 2010 Subaru Forester. You need to make a new mounting hole for the front speakers and it just barely works. The back are too far away to use. These adapters are NOT recommended for the 2010 Subaru Forester no matter who tells you it will work.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Fit great and made the speaker installation a breeze.

Have questions for
?

Not for 2010 Suburu Forester

Crutchfield site said these would fit my 2010 Suburu Forester. I tried every orientation possible and only 2 out of 3 screw holes would line up with holes in door. I ended up drilling a new hole in the bracket.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

These did not fit my 2007 Equinox front doors and came with no instructions to indicate any alterations were needed to fir the back doors. Modifications to the both the brackets and some metal work to the door were needed to make these work in the front. I had to remove tabs from the brackets so that the Focal speakers would fit the bracket for all doors. With no instructions indicating modifications were expected, this was a frustrating phase of the project.

Have questions for
?

Needed accessory

Adapters worked well for the front door location of my '01 Saturn L200, once I figured out the necessary modifications needed to complete the install. A welcome and free piece of hardware to make the install a little easier.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Maybe I was sent the wrong brackets, but I'm sorry these were a real pain. The speakers do not, repeate do not fit these. I finally went and purchased longer screws and installed these brackets backwards to get my speakers installed. I know it's wrong but I wanted my tunes.

Have questions for
?

Perfect fit

Perfect fit for enlarged holes.

Have questions for
?

Makes it so much easier.

Made all the difference. Mounted speaker to it and mounted bracket to door. DONE. I tried to install the rear speakers without it and it didn't work, ended up buying a this bracket for the rear as well. Install for dummies ... that is how easy it makes it.

Have questions for
?

Didn't fit

Didn't fit the car. At all. Wrong size. Wrong screw holes didn't even fit the speakers

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Only matches 2 of the three mounting holes on my subaru so the y rattle a little

Have questions for
?

Perfect for replacing my factory speakers

These brackets were a necessary evil due to the fact my factory speakers were installed using rivots. They were included in the purchase of speakers and worked great.

Have questions for
?

Worthless

If I could give these a 0 rating I would. Completely useless In my 2015 Lancer. They came with the Jensen Dubs 5 1/4" speakers for my front and back doors. Not only did they fit the door poorly requiring me to drill all new holes, the speakers didn't fit them either!

Have questions for
?

Please send the right speaker mounts for JBL Stage 600c 6-3/4 speakers

The speaker mounts fit fine onto the door and holes for the screws matched up well. These mounts were shipped with the JBL-Stage-600C-6-3/4" Item #109STAGE6C. The speakers don't fit into the mounts and I am unable to secure the speakers to the mounts. I have to reinstall the factory speakers to the car now. Not a happy customer.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Fit my 2016 Subaru Impreza front door speakers with only minor modification.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

They fit, and work well. What more can I say.

Have questions for
?

Work as expected, sturdy, and free from Crutchfield

These worked fairly well. I used them to install JVC CS-DR620 6 1/2" speakers (front & rear) in a 2008 Subaru Impreza WRX. The instruction PDF you can download for it is pretty useless. It only says you can remove the inner tabs, which I didn't have to. If you plan to use these, the side with the lip should be installed against the car door. I was able to mount the bracket using the two lower (left & right) factory holes for the front and drilled the top hole. It says use a 1/8" drill bit, but you have to make the hole a little bigger for the factory screw to fit. For the rear speakers, I was able to arrange the bracket so I could use the top factory hole and lower left factory hole and had to drill one hole for the lower right. I used the screws that came with the JVC speakers to the bracket. I just screwed it to the plastic as the metal clips supplied with the speakers can't be used with the bracket. Also, there is also no slot to run the speaker wire, I just pinched it between the speaker and the bracket, didn't seem like a big deal. They were free and they work, not much more you can ask for. I think some people expect solid gold brackets that fit every vehicle ever made for free. I appreciate that Crutchfield provides these for free and they only require a small modification and some common sense. I'm happy with them, I'd give them 3 1/2 stars.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

These do the job, easy to use and modify.

Have questions for
?

terrible

If i could give these no stars i would. they do not fit the new speakers at all. i had to drill all new holes for the speaker to fit. i also had to go to the hardware store to get new screws to work with these. I was told when i got them that i would have to drill one hole in my car. I did have to do that but i did not think i would have spent an hour just messing around trying to get them to work with the speaker and with the car itself. they did not come with any instructions on how to use them and they didnt come with any screws and the screws that came in the factory speakers would not have worked for these they were too short. they also need a hole for the speaker wires to go through. I really wish i had looked into getting something that would have fit 100%. I know that they gave me them for free but i would have paid to have something that i didnt need to modify so much.

Have questions for
?

works

worked in my 2016 kia rio 5 which has stock 6.5 speakers. only issue was out of the 3 mounting holes only 2 can be used. the 3 u need to use a washer on the screw to catch the bracket.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Received with a speaker up-grade I purchased for a 2010 Forester. Useless, did not come close to aligning with the door frame or the new speaker, I would have had to drill at least 5-6 holes in each inner door frame to use this bracket. And after all that the support would still be questionable. Since the install was in an SUV, that fact made them useless. I decided to gut the OEM speakers, using the plastic surround/frame as a new mounting bracket. This change reduced the drilling per door in half and the end result looked and performed like a factory install. I called tech support during the early stages of the install. I was treated like a novice. The tech did not want to hear about the fact they did not fit. He stated the SD speakers came with self-tapping screws. Gee, thanks bro. This was a surprise, first time in 30 years doing business with Crutchfield that tech support did not come through.

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Excellent fit to my '07 Sonata door.

Have questions for
?

Doesn't fit.

For some reason Crutchfield thinks these fit my 2013 Impreza WRX STi, they do not. The factory speaker mounting holes do not match theses speaker brackets, so a new hole has to be drilled. Another hole also needs to be drilled to allow the speaker wires to pass through from behind the speaker.

Have questions for
?

Did Not fit

Product did not fit the car as described, had to drill new holes in door to get speaker to fit. Would not have rated it a 2 if there was something that indicated that may be necessary

Have questions for
?

Scosche SAGMEQ656 Speaker Mounting Brackets

Great fit, exactly as described.

Have questions for
?