About the MTX THUNDER1000.1
Upgrade your power for better sound
Upgrade your power for better sound
You'll get some serious MTX bass mojo when you put the THUNDER1000.1D mono amp in your car. This compact amp will drive your subwoofer setup with up to 1,000 watts RMS. Hook this amp up to a nice set of subs, and you'll hear sounds you've never heard before, even in your favorite songs.
MTX knows that your system changes over time, and this amp will adapt to almost any subwoofer situation. It'll send 350 watts to a single 4-ohm sub now, but it's capable of delivering up to an awesome 1,000 watts to a 1-ohm load, so you don't have to buy a new amp to handle a multiple sub setup later on. It's amazing to think that so much power comes from an amp that'll almost fit on a piece of computer paper. This little bruiser will truly fit in places where amps don't usually go.
Advanced tone control
You can adjust the low-pass filter and subsonic filter to get the best possible sound from your sub and enclosure. In the unlikely event you want to bump up the bass a little, you also have access to a selectable bass boost.
MTX THUNDER1000.1 control panel
- mono subwoofer amplifier
- 350 watts RMS x 1 at 4 ohms (600 watts RMS x 1 at 2 ohms)
- 1,000 watts RMS x 1 at 1 ohm
- variable low-pass filter (40-220 Hz, 12 dB/octave)
- selectable bass boost (0, 6, 12 dB at 50 Hz)
- variable subsonic filter (10-50 Hz, 12 dB/octave)
- frequency response: 20-220 Hz
- preamp inputs
- 4-gauge power and ground leads and a 100-amp fuse recommended wiring and hardware not included with amplifier
- no onboard fuses — when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended
- 12-5/8"W x 2-1/4"H x 6-5/16"D
- warranty: 2 years
- Our 60-day money-back guarantee
- MFR # THUNDER1000.1
What's in the box:
- Mono subwoofer amplifier
- 4mm Allen wrench
- 2mm Allen wrench
- Four 1/2" Self-tapping screws
- Owner's manual (English/ Spanish/ Portuguese/ French)
More details on the MTX THUNDER1000.1
Features & specs
|RMS Power Output (Watts x Channels)||
350 x 1 |
|Peak Power Output (Watts x Channels)||2000 x 1|
|Power at 2 Ohms (Watts x Channels)||600 x 1|
|Bridged Power (Watts x Channels)||N/A|
|Minimum Impedance Bridged||N/A|
|Minimum Impedance Unbridged||1|
|Best Frequency Response||20-220 Hz|
|THD at Rated RMS Power||0.3%|
|Signal to Noise Ratio||75 dB|
|Low-Pass Crossover Frequency||40-220 Hz|
|Low-Pass Slope (dB/octave)||12 dB/octave|
|High-Pass Crossover Frequency||N/A|
|High-Pass Slope (dB/octave)||N/A|
|Bass Boost||0, 6, 12 dB|
|Bass Boost Frequency||50 Hz|
|Speaker Level Inputs||---|
|Parts Warranty||2 Years|
|Labor Warranty||2 Years|
Overview: The MTX Thunder1000.1 is a mono Class D subwoofer amplifier. It has aluminum heatsinks to dissipate heat generated by the amplifier. The amp produces 350 watts RMS x 1 at 4Ω, 600 watts RMS x 1 at 2Ω, and 1000 watts RMS x 1 at 1Ω.
Gain: The amp's rotary gain control is continuously variable from 200mV to 5V to match the output of the source unit.
Protection Circuits: The Thunder1000.1 provides protection against overheating, under voltage, and electrical short circuits.
Crossovers: The amp features a built-in low-pass crossover, with a continuously variable cutoff frequency of 40-220Hz; the crossover cannot be bypassed. Additionally, the amp has a subsonic filter to remove ultra-low frequencies, thus minimizing wasted power and protecting speakers not capable of reproducing those frequencies. It has a variable crossover frequency of 20-50Hz.
Bass Boost: The Thunder1000.1's bass boost circuit is centered at 50 Hz. It can be set to 0dB, +6dB, or +12dB.
Electronic Bass Control (EBC): An Electronic Bass Control (EBC) module is available directly from MTX that allows you to adjust the bass output of the amplifier from the front of the vehicle.
Power Terminals: The Thunder1000.1 features set screw terminals for power, ground and remote turn-on. The power and ground terminals will accommodate up to 4 AWG wire, while the remote turn-on terminal will accept up to 10 AWG wire. The set screws are loosened/tightened with the supplied Allen wrenches. MTX recommends the use of 4 AWG power and ground wires.
Note: The Amplifier is not equipped with an internal fuse. An external 100-amp fuse (not included) must be installed on the power wire. If the system has only this amp and a wiring kit is used that includes a fuse with a value other than 100-amps, the original should be replaced with a 100-amp fuse.
Speaker Connections: The amplifier is equipped with two pair of set screw terminal speaker outputs. The outputs are internally wired in parallel, making it easy to connect two subwoofers. Each terminal will accommodate up to 10 AWG bare wire and is loosened/tightened with the supplied Allen wrench.
EBC Port: The amp has a 3.5mm mini-jack for plugging in an optional Electronic Bass Control (EBC) module, currently available directly from MTX.
4 questions already asked