Contact us
Close contact box

MTX WET75.2

2-channel marine amplifier — 75 watts RMS x 2 at 4 ohms

Item # 236WET752

Item # 236WET752

Ships from distributor

In stock

C$329.99 -C$30.00 Price break

C$299.99

About the MTX WET75.2

MTX gets WET

MTX brings their years of land-based experience to the water with their WET Series marine components. Based on their Thunder Series amps, the WET75.2 amplifier is designed to power your speakers under seriously adverse conditions. Its weather-resistant features include a conformal coated circuit board, stainless steel hardware, rubber gaskets around the RCA connectors, and plastic control covers to keep moisture from getting to the amplifier. The 75.2 also features MTX's surface mount technology, which attaches critical components directly to the circuit board to minimize the effect of vibration.

MTX WET75.2 100W x 2 Marine Amplifier

This rugged MTX amp is built to stand up to life on a boat.

Power and control

Behind the weatherproofing and the construction, you'll find a Class A/B 2-channel amplifier which delivers 75 watts per channel at 4 ohms, or 100 watts per channel at 2 ohms. The 75.2 features a high-pass crossover variable from 10 to 200 Hz, so you can remove low bass from your full-range speakers when you're using a sub.

And MTX made this amp to fit the tight spaces in a boat, with a small footprint that allows it to go almost anywhere and an extruded heat sink that'll keep things cool. It's ready to make waves. Are you?

Product highlights:

  • 2-channel marine amplifier
  • Class A/B design
  • 75 watts RMS x 2 at 4 ohms (100 watts RMS x 2 at 2 ohms)
  • variable high-pass crossover: 10-200Hz at 12 dB/octave
  • conformal-coated circuit board
  • weather-resistant construction
  • dimensions: 7-7/8"W x 6-3/8"D x 2-1/4"H
  • warranty: 2 years
  • Our 60-day money-back guarantee
  • MFR # WET75.2

What's in the box:

  • 2-Channel amplifier
  • 4mm Allen wrench
  • 2mm Allen wrench
  • Four 5/8" Stainless steel self-tapping screws
  • Owner's manual (English/ Spanish/ Portuguese/ French)

Customer reviews

Loading reviews...

MTX WET75.2 reviews

Average review:

2 reviews

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

Product Research

Features
Connections

Features

Overview: The MTX WET75.2 is a full range 2-channel amplifier designed for the harsh marine environment. The amp features a conformal coated PCB, covered controls, rubber gaskets around the RCA inputs, and stainless steel mounting hardware. The output power is 75 watts RMS x 2 at 4Ω, 100 watts RMS x 2 at 2Ω, and 200 watts RMS x 1 bridged at 4Ω.

Note: The cover over the gain and crossover controls is held in place by two 2.5mm Allen head screws; no 2.5mm Allen wrench is included with the amp.

Gain: The amp's rotary gain control is continuously variable from 200mV to 5V to match the output of the source unit.

Protection Circuits: The WET75.2 provides protection against overheating, under/over voltage, and electrical short circuits.

Crossovers: The built-in crossover is switchable between low-pass, full range, and high-pass. The crossover point (high-pass or low-pass) is continuously variable from 50 Hz to 750 Hz.

Connections

Power Terminals: The WET75.2 features set screw terminals for power, ground and remote turn-on. The power and ground terminals will accommodate up to 4 AWG wire, while the remote turn-on terminal will accept up to 10 AWG wire. The set screws are loosened/tightened with the supplied Allen wrenches.

Note: The Amplifier is not equipped with an internal fuse. An external 30-amp fuse (not included) must be installed on the power wire. If the system has only this amp and a wiring kit is used that includes a fuse with a value other than 30-amps, the original should be replaced with a 30-amp fuse.

Speaker Connections: The amplifier is equipped with two pair of set screw terminal speaker outputs. Each terminal will accommodate up to 10 AWG bare wire and is loosened/tightened with the supplied Allen wrench.

Loading accessories...

Customer Q&A

Loading articles...

TOP