Contact us
Close contact box

MTX XTHUNDER800.5

5-channel car amplifier — 75 watts RMS x 4 at 4 ohms + 400 watts RMS x 1 at 2 ohms

Item # 236XT8005

If you're looking for high power for your car's audio system, look no further than the XTHUNDER800.5...

If you're looking for high power for your car's audio system, look no further than the XTHUNDER800.5...

Item # 236XT8005

Ships from distributor

In Stock

C$799.99 Sale: -C$100.00 off

C$699.99
Add to wishlist

About the MTX XTHUNDER800.5

Versatile amp for your whole system

If you're looking for high power for your car's audio system, look no further than the XTHUNDER800.5 amplifier from MTX. This X-Thunder Series 5-channel amp can drive your front and rear speakers with 75 watts RMS each while powering a subwoofer with up to 400 watts RMS. You can also set this amp up into 3-channel mode to power a pair of high-powered speakers or components with 250 watts each, along with sending 400 watts to your sub.

Versatile amp for your whole system

If you're looking for high power for your car's audio system, look no further than the XTHUNDER800.5 amplifier from MTX. This X-Thunder Series 5-channel amp can drive your front and rear speakers with 75 watts RMS each while powering a subwoofer with up to 400 watts RMS. You can also set this amp up into 3-channel mode to power a pair of high-powered speakers or components with 250 watts each, along with sending 400 watts to your sub.

Controls for superior tone

In addition to the power available, the XTHUNDER800.5 features variable high-pass filters on the front and rear channels to optimize your speakers' response, and a low-pass filter on the sub channel for the subwoofer. The variable bass boost on the sub channel adds just the right amount of low-frequency oomph.

READ LESS

Product highlights:

  • 5-channel car amplifier
  • 75 watts RMS x 4 + 300 watts RMS x 1 at 4 ohms
  • 125 watts RMS x 4 + 400 watts RMS x 1 at 2 ohms
  • 250 watts RMS x 2 bridged at 4 ohms + 400 watts RMS x 1 at 2 ohms
  • Class D amp technology
  • variable high-pass filters (40-250 Hz, 12 dB/octave) on front and rear channels
  • variable low-pass filter (40-250 Hz, 12 dB/octave) on subwoofer channel
  • variable bass boost (0-18 dB at 45 Hz) on subwoofer channel
  • preamp and speaker-level inputs
  • fuse rating: 40A x 2
  • 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
  • dimensions: 14-1/8"W x 2-1/16"H x 8-15/16"D
  • warranty: 2 years
  • Our 60-day money-back guarantee
  • MFR # XThunder800.5
KEEP READINGREAD LESS

What's in the box:

  • 5-Channel amplifier with two 40A ATC fuses installed
  • 2mm Allen wrench
  • 2.5mm Allen wrench
  • 3mm Allen wrench
  • 8" Speaker-level input harness (with an 8-pin Molex plug on one end)
  • 4 Self-tapping screws (Length=3/4")
  • Owner's Manual

Customer reviews

Loading reviews...

MTX XTHUNDER800.5 reviews

Average review:

1 review

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Thunder Amp!!!

Mike B. from El Paso, TX on 10/16/2014

Verified customer (What's this?)
Verified employee purchase (What's this?)

The MTX Thunder 800.5 pushes an intense amount of power to 2 sets of speakers and 2X12" box. All my speakers are alive and kicking.

Pros: Mounts just about anywhere and really delivers the power I needed.

Cons:

Crutchfield response on

4 of 4 found this helpful

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

Product Research

Features
Controls
Connections

Features

Class D 5-channel Amplifier: The MTX XTHUNDER800.5 is designed to power four full-range speakers and a subwoofer. The amp's Class D design and extruded aluminum top cover keeps the amplifier running cool.

Circuitry: MTX X-Thunder amplifiers feature dual-sided circuit boards with increased copper traces for maximum current transfer and to avoid power loss. Surface-mounted components increase durability and resistant to vibrations.

Power Output: The XTHUNDER800.5 produces 75 watts RMS x 4, plus 300 watts x 1 at 4 ohms. At 2 ohms, the output is 125 watts RMS x 4, plus 400 watts.

Protection Circuits: The XTHUNDER800.5 provides Thermal, Short circuit, and Over- and Under-voltage protection with an LED indicator.

Auto Turn-on: The amp features automatic turn-on circuitry which allows installation via high-level input without the use of a remote wire. When an audio signal is detected on the high-level input, the amplifier will turn itself on. The Remote Turn-on switch should be in the "Auto" position.

Controls

Input Level: The amplifier is divided into three sections: front, rear, and subwoofer channels. Each section has an Input Level control, which helps you match the amplifier's sensitivity to the signal voltage of the source unit. A small screwdriver is required to set the input level.

Crossovers: The XTHUNDER800.5 features separate 12 dB/octave crossovers for the front and rear channels. Each crossover is variable with a 40Hz to 200Hz cutoff frequency, and can be configured as High-pass or bypassed (Full-range). In addition, the subwoofer channel has a non-defeatable low-pass filter with an adjustable cutoff frequency of 40-200Hz. A small screwdriver is required to adjust the cutoff frequency.

Bass Boost: The amplifier has a bass boost circuit for the subwoofer channel only. The amount of boost is adjustable from 0-18dB at 45Hz.

Connections

Power/Ground/Turn-On Connections: The XTHUNDER800.5 features set-screw terminals for the Power, Ground and Remote turn-on lead. The terminals can be tightened/loosened with the supplied 3mm and 2.5mm Allen wrenches. The Power and Ground terminals will accommodate up to a 4 AWG wire (minimum of 8 AWG wire is recommended). An in-line fuse holder with an 80A fuse (or next highest available) should be placed on the power wire within 18" of the positive battery terminal. Typically, an 18 AWG turn-on lead is included with most amp wiring kits. If using the Speaker Level Input, no turn-on lead is needed.

RCA Inputs: The three pairs of RCA input jacks are for connecting source units with preamp outputs. If your head unit does not have three pairs of preamp outputs, you can connect two pairs from the head unit. The subwoofer channel can receive audio from the rear channels if the amp's Input Mode switch is placed in the "4CH" position. The low-level input sensitivity range is 200mV to 5V. When using the RCA inputs, you should place the Remote Turn-on switch to the "EXT" position.

Speaker Level Input: The XTHUNDER800.5 comes with a 4-channel speaker level input harness, allowing you to connect a factory radio or a receiver with no preamp outputs. With the Input Mode switch in the "4CH" position, the subwoofer will receive a signal from the rear channels. After splicing front and rear, left and right speaker wires to the speaker-level input harness, the harness plugs into the amplifier's Molex connection. When using the speaker-level inputs, the amp automatically turns on when it senses signal from the head unit, eliminating the need for a remote turn-on connection. In many cases, this feature will allow you to install the amplifier without removing your radio. The Remote Turn-on switch should be in the "Auto" position.

Speaker Connections: The amplifier is equipped with four pairs of speaker terminals for connecting four full-range speakers, and one pair for hooking up the subwoofer. The set-screw speaker terminals will accommodate 12 to 10 AWG speaker wire, and can be tightened/loosened with the supplied 2mm Allen wrench.

Remote: The amp has an RJ-25 jack for connecting the optional Electronic Bass Control.

Fuses: The amplifier is equipped with two 40-amp ATC-type fuses.

Loading accessories...

Customer Q&A

Loading articles...

TOP