About the CRUX SWRVW-52 Wiring Interface
Wire in a new radio
You'll only be able to retain your steering wheel audio controls with a compatible car stereo made by Alpine, Boss, Blaupunkt, Clarion, Dual, Jensen, JVC, Kenwood, Pioneer, Sony or Soundstream. No other brands are currently compatible.
Wire in a new radio
Crux's SWRVW-52 interface ensures that you can keep the steering wheel audio controls and the factory amplifier (if present) in your Volkswagen when you replace the factory radio. Once you connect this interface to the wires on your new stereo's wiring harness, you've covered the power, ground, and factory speaker connections for your new stereo.
The SWRVW-52 interface also offers the reverse, illumination, and Vehicle Speed Sensor (V.S.S.) outputs that you'll need if you're installing a navigation receiver. The Crux interface is designed to work with the factory Volkswagen CAN-bus systems.
Note: This interface will retain steering wheel audio controls when used with compatible Alpine, Boss, Blaupunkt, Clarion, Dual, Jensen, JVC, Kenwood, Pioneer, Sony or Soundstream receivers.
Product highlights:
- connect a new stereo in select 2002-13 VW models
- retain your steering wheel audio controls with select car stereos
- provides connections for Vehicle Speed Sensor (V.S.S.), reverse gear, and illumination for installing navigation receivers
- works with factory amplified systems
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # SWRVW-52
What's in the box:
CRUX SWRVW-52 Wiring Interface owner's manual
- Radio replacement interface module (for Volkswagen)
- Wiring harness
- SWC harness
- Installation Instructions
Reviews
Customer reviews
Loading reviews...
CRUX SWRVW-52 Wiring Interface reviews
Average review:
Customer photos
More details on the CRUX SWRVW-52 Wiring Interface

Product Research
Features
Volkswagen Radio Replacement Interface: The CRUX SWRVW-52 is a radio replacement interface for select 2002-up Volkswagen vehicles (w/ CAN bus systems). It facilitates the integration of an aftermarket radio to enable retention of factory features when replacing a factory installed radio in select Volkswagen cars (with or without factory-installed amps). This interface is also pre-programmed for retention of steering wheel controls.
Compatibility: The CRUX SWRVW-52 is supported by the following 2002-up Volkswagen vehicles with CAN bus systems and non-amplified or amplified factory audio systems.
Make | Model | Year |
Volkswagen | Beetle | 2012-2013 |
CC | 2009-2013 | |
EOS | 2006-2012 | |
Golf | 2002-2013 | |
GTI | 2006-2013 | |
Jetta | 2002-2013 | |
Passat | 2002-2013 | |
Rabbit | 2006-2011 | |
Tiguan | 2009-2013 | |
Touareg | 2004-2010 |
Steering Wheel Control Retention: The CRUX SWRVW-52 also features a steering wheel control output for Pioneer, Sony, Alpine, Clarion, Kenwood, JVC, Jensen, Dual/Axxera, Boss and other aftermarket head units. The steering wheel control output consists of a right-angle 3.5mm connector and a light blue/yellow wire (use the connection that your aftermarket head unit is fitted with). The SWRVW-52 interface module will work with any of the listed aftermarket head units, by setting its three dip-switches (see owner's manual for appropriate setting).
Note: The steering wheel control harness features two 4-pin connectors, two 3.5mm connectors (labeled Pioneer/Sony and Alpine/Clarion/Jensen/Dual/Boss), and one blue/yellow wire (labeled Kenwood/JVC). You will only plug in one of the 4-pin connectors to the interface module and one of the 3.5mm connectors or blue/yellow wire into your aftermarket head unit you are installing.
Navigation Outputs: The CRUX SWRVW-52 radio replacement interface module provides a VSS (vehicle speed sense) and a Reverse Gear output to make installing an aftermarket Navigation radio simpler and less time consuming.
Amp Turn-On: The CRUX SWRVW-52 provides an amplifier turn-on lead for your vehicle's factory amplifiers (if equipped).
RAP: In most vehicles your aftermarket head unit will continue to operate with the vehicle's RAP (Retained Accessory Power) system; the aftermarket radio will stay on until the key is fully removed from the ignition switch. However, in 2010-up vehicles with premium sound the RAP feature will not be retained; the radio will shut off when the key is turned off
Wiring Harness: The included wiring harness features a 40-pin connector which plugs into your vehicle's factory radio harness, plus a 12-pin connector which plugs into the SWRVW-52 interface module. The wiring harness also provides the following bare-wire leads which will need to be hardwired to your aftermarket head unit's wiring harness.
Wire Color | Function |
Black | Chassis Ground |
Red | +12 Volt Accessory |
Yellow | +12 Volt Constant |
Orange | Illumination |
Blue | Amp Turn-On |
White | Left Front Speaker + |
White/black | Left Front Speaker - |
Gray | Right Front Speaker + |
Gray/black | Right Front Speaker - |
Green | Left Rear Speaker + |
Green/black | Left Rear Speaker - |
Purple | Right Rear Speaker + |
Purple/black | Right Rear Speaker - |
Orange/white | VSS (vehicle speed sensor) |
Red/white | Reverse |
Loading accessories...
Customer Q&A
7 questions already asked
Loading articles...