Chat
Contact us
Close contact box
Connect ID #
672 374 43
Connect ID #
672 374 43
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

Our contact center is currently closed.

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-888-292-2575

Thank you, !
Our conversation will be emailed to
Please enter a question  
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  

Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

PAC HDK001X Dash and Wiring Kit

Install and connect a single-DIN receiver in select 1998-2013 Harley-Davidson models

Item # 541HDK001X

This PAC HDK001X factory dash and wiring kit allows you to install a single-DIN (2" tall) radio in select...

Find what Fits your car

This PAC HDK001X factory dash and wiring kit allows you to install a single-DIN (2" tall) radio in select...

Item # 541HDK001X

In stock
C$164.99

About the PAC HDK001X Dash and Wiring Kit

PAC HDK001X

This PAC HDK001X factory dash and wiring kit allows you to install a single-DIN (2" tall) radio in select 1998-2013 Harley-Davidson models with factory fairings. It includes a pre-programmed interface to retain the factory handlebar audio controls and a pre-wired installation harness that requires no cutting of any factory wires. The kit features two options of frames for the aftermarket radio installation (with or without a hinged tinted/UV protective cover). Warranty: 1 year.

PAC HDK001X

This PAC HDK001X factory dash and wiring kit allows you to install a single-DIN (2" tall) radio in select 1998-2013 Harley-Davidson models with factory fairings. It includes a pre-programmed interface to retain the factory handlebar audio controls and a pre-wired installation harness that requires no cutting of any factory wires. The kit features two options of frames for the aftermarket radio installation (with or without a hinged tinted/UV protective cover). Warranty: 1 year.

Note: You'll only retain your handlebar audio controls with cars stereos made by  Alpine, Clarion, Dual, Kenwood, Jensen, JVC, Pioneer, Sony, or Valor.

READ LESS

What's in the box:

  • Radio housing
  • Radio housing w/ splash-guard
  • Handlebar control interface module
  • Wiring harness
  • Rubber gasket (pre-installed)
  • 2 Brackets
  • 2 Spacers
  • 4 Long bolts
  • 4 Short bolts
  • 4 Hex-nuts
  • 4 Screws
  • Instructions
MFR #HDK001X

Customer reviews

Loading reviews...

PAC HDK001X Dash and Wiring Kit reviews

Average review:

11 reviews

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

More details on the PAC HDK001X Dash and Wiring Kit

Stacey B.

Product Research

Features

Harley Davidson Radio Replacement Kit: The PAC HDK001K radio replacement kit makes it possible for Harley Davidson motorcycle enthusiasts to integrate an aftermarket radio into their ride. This Harley Davidson radio replacement kit includes a pre-programmed interface to retain the factory handlebar audio controls, installation harness, two options of radio housings for the aftermarket head unit installation, and mounting hardware.

Compatibility: The PAC HDK001X is compatible with select 1998-2013 Harley-Davidson motorcycles and most aftemarket radios with a wired remote input that are steering wheel control ready.

  • VehicleThe PAC HDK001X is compatible with select 1998-2013 Harley-Davidson motorcycles (FL models with factory fairings). The PAC HDK001X does not retain rear speakers; these will need to be hard wired.
  • Radio: The aftermarket radio must be equipped with a wired remote input (3.5mm headphone style jack or Blue/Yellow wire) to be compatible. Not compatible with Sony XAV series head units; Kenwood KDC-X598, KDC-BT318U, KDCBT-758-HD, KDCBT-558U and KDC-X798 head units, and Alpine UTE-73BT, CDE-172BT, CDE-173BT and CDE-175BT head units.

Radio Housing: The PAC HDK001X comes with two radio mounting kits that will fit most single-DIN aftermarket head units. One of the mounting kits features a hinged tinted/UV protective cover, while the other mounting kit does not.

Retains Handlebar Audio Controls: The included SWI-HD interface module allows you to retain your Harley Davidson's handlebar audio controls. The included SWI-HD interface module is compatible with Alpine, Clarion, Dual, Kenwood, Jensen, JVC, Pioneer, Sony, & Valor aftermarket head unit's that features a SWC input (3.5mm) or SWC wire (Blue/Yellow). The interface comes pre-programmed, but can also be reconfigured.

Wiring Harness: The PAC HDK001X comes with a wiring harness which plugs directly into the included interface module and your Harley Davidson's factory radio plug. You will need to hard-wire the following seven wires of the harness to your new aftermarket head unit's wiring harness.

Wire Color Function
Yellow +12 Volt Constant
Black Ground
Red +12 Volt Accessory
White Left Front Speaker +
White/black Left Front Speaker -
Gray Right Front Speaker +
Gray/black Right Front Speaker -

Installation Note: Factory CB, intercom, and rear volume control functions are integrated into the Harley Davidson stock radio and cannot be retained when adding an aftermarket radio. Depending on bike configuration it may be necessary to install new rear speaker wires.

Loading accessories...

Customer Q&A

5 questions already asked

Q
Will this Dash and Wiring Kit paired with a Sony DSX-M55BT work on my 2005 Harley Davidson FLHTCSE2 CVO model?
[ JAMES  Aug 29, 2020 ]
1 answer
A
More than likely, I installed it in my 2010 Ultra Classic CVO and it fit perfectly....nice kit overall....
[ Pat  Aug 30, 2020 ]
Q
Will this work with Kenwood kmr m322 bt?
[ Rob  Feb 25, 2018 ]
1 answer
A
Yes. The kit is made for use with standard single DIN chassis stereos and the Kenwood KMR-M322BT stereo is a standard single DIN chassis model. I hope that helps. My bio: https://www.crutchfield.com/bio/Ryan
[ Ryan  Mar 14, 2018 ]  Staff
Q
Will this allow the rear speakers on my ultra to power on too ?
[ Norm  Oct 04, 2017 ]
3 answers
A
Yes it will. It worked on my Electra Glide
[ do not want bus  Oct 04, 2017 ]
A
Yes
[ chad  Oct 04, 2017 ]
A
No it will not. U will have to find the wires to the rear speakers and connect them to the radio.
[ Jonathan  Oct 04, 2017 ]
Q
is this in stock?
[ Debbie  Mar 15, 2017 ]
1 answer
A
Thanks for your question. Yes we currently have 30+ in our warehouse. Hope that helps.
[ Kenny  Mar 15, 2017 ]  Staff
SHOW MORESHOW LESS

Loading articles...

TOP