About the Rockford Fosgate M400-4D
High power from a compact amp
High power from a compact amp
Rockford Fosgate's compact marine amplifiers provide high-efficiency Class-D power for your marine audio system. They meet tough UV and Salt-Fog protection standards, so you can install them with confidence in your pleasure craft, whether you're blasting across inland waterways, or cruising out to your favorite salt-water fishing grounds.
Power your speakers or subs
The M400-D4 4-channel amp delivers the power you need to drive two pairs of full-range speakers in your boat, sending 75 watts continuous power to each speaker. If you want to power a pair of subs, you can bridge the amp to 2-channel mode, sending 200 watts to each subwoofer — plenty of kick if you want some bass on board.
The amp features variable frequency filters to adjust the amp's output to your system, whether you're running full-range speakers or subs. And the compact footprint makes it easy to mount the amp in a small storage locker or other tight spot.
- 4-channel marine amplifier
- 75 watts RMS x 4 at 4 ohms (100 watts RMS x 4 at 2 ohms)
- 200 watts RMS x 2 in bridged mode (4-ohm stable in bridged mode)
- conformal-coated circuit board and UV-resistant finish
- variable high- and low-pass filters (50-500 Hz, 12 dB per octave)
- variable bass boost (0-12 dB at 45 Hz)
- three auto-turn on modes
- CEA-2006 compliant
- preamp-level inputs and outputs
- 4-gauge power and ground leads recommended wiring and hardware not included with amplifier
- 9-1/8"W x 2"H x 6-7/8"D
- warranty: 1 year
- Our 60-day money-back guarantee
- MFR # M400-4D
What's in the box:
- 4-Channel marine amplifier
- 3mm Hex key
- 4 Self-tapping screws (length=1-5/8")
- Installation & Operation Manual
- Amplifier Verification Certificate
More details on the Rockford Fosgate M400-4D
Features & specs
|RMS Power Output (Watts x Channels)||75 x 4|
|Frequency Response at Rated RMS Power||20-20k Hz|
|THD at Rated RMS Power||1%|
|Signal to Noise Ratio||70 dB|
|Peak Power Output (Watts x Channels)||---|
|Power at 2 Ohms (Watts x Channels)||100 x 4|
|Bridged Power (Watts x Channels)||200 x 2|
|Minimum Impedance Bridged||4|
|Minimum Impedance Unbridged||2|
|Low-Pass Crossover Frequency||50-250 Hz|
|Low-Pass Slope (dB/octave)||12 dB/oct|
|High-Pass Crossover Frequency||50-250 Hz|
|High-Pass Slope (dB/octave)||12 dB/oct|
|Bass Boost||0-18 dB|
|Bass Boost Frequency||45 Hz|
|Speaker Level Inputs||No|
|Preamp Outputs||1 pair|
|Parts Warranty||1 Year|
|Labor Warranty||1 Year|
Overview: The Rockford Fosgate Prime Marine M400-4D is a 4-channel full-range Class D marine amplifier. It is optimized to power a full-range front/rear speaker system. You can also bridge the front and/or rear channels to run a subwoofer or two. The Class D design is very efficient with a cast aluminum heatsink to keep it in a small footprint.
Marine Amplifier: The M400-4D is designed for the harsh marine environment. The amplifier features a conformal-coated PCB and UV-resistant finish, and conforms to UV and Salt-Fog protection standards.
CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for determining an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured into a 4-ohm load with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4 ohms. CEA-2006 allows consumers to compare amplifiers and receivers on an equal basis. The CEA-2006-rated RMS power output is as follows (measured with a 14.4 volt input, <1% THD+N, 20 Hz-250 Hz):
- 4-Ohm: 75 watts x 4
- 2-Ohm: 100 watts x 4
- Bridged (4-Ohm): 200 watts x 2
LED Indicator: The amplifier is equipped with a top-mounted LED indicator which illuminates blue when the unit is turned on. The LED illuminates red when a protection circuit engages (short circuit or too low an impedance is detected at the speaker connections). The amplifier automatically turns off if this occurs.
Mounting: The amplifier can be mounted vertically, horizontally, or inverted using the supplied mounting screws; horizontal mounting (right side up) will provide the best cooling.
Independent Controls: The M400-4D has independent, top-mounted controls for the front and rear channels. The controls include:
- Gain Control: The amplifier has rotary gain controls (0 to 11) for front and rear channels.
- Crossovers: The amplifier features independent Butterworth crossovers for the front and rear channels. Each crossover can be set for low-pass, high pass, or all-pass (full range). The crossover frequency is continuously variable from 50-250 Hz with a slope of 12 dB per octave.
Punch EQ: The rear channel has an independent Punch EQ (bass boost) control that works with the crossover switch. When the rear channel crossover is set to low-pass, the Punch EQ can add a bass boost, centered at 45 Hz, from 0 dB to +18 dB.
2/4 CH Switch: When the 2/4 CH switch is set to the 2 CH position, the inputs are switched to a 2-channel mode. The signal on the front input feeds all four output channels, however, you lose front to rear fading capability. In the 4 CH position, the amp uses both front and rear inputs and fading capability is restored.
Power Terminals: The power and ground terminals are nickel-plated set-screw terminals, and will accommodate up to 4-gauge wire. The set screws can be tightened/loosened with the supplied 3mm hex key.
Fuses: The amplifier does not have on-board fuses. A 40A fuse should be placed on the power wire within 18" of the battery.
Remote Turn-On Terminal: The remote turn-on terminal is a nickel-plated set-screw terminal that will accommodate up to 8-gauge wire. The set screws can be tightened/loosened with the supplied 3mm hex key.
Speaker Terminals: The speaker terminals are nickel-plated set-screw terminals that will accommodate up to 8-gauge wire. The set screws can be tightened/loosened with the supplied 3mm hex key.
RCA Input Jacks: There are two pairs of RCA input jacks for the front and rear channels. They are nickel-plated to resist signal degradation caused by corrosion.
RCA Pass-Thru Jacks: The nickel-plated RCA pass-thru jack provides a convenient source for daisy-chaining an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the amplifier location.
1 question already asked