Contact us
Close contact box

Rockford Fosgate Punch P300X1

Mono amplifier — 300 watts RMS x 1 at 2 ohms

Item # 575P300X1

Rockford Fosgate's Punch P300X1 mono amplifier produces up to 300 watts RMS, giving you plenty of clean power...

Rockford Fosgate's Punch P300X1 mono amplifier produces up to 300 watts RMS, giving you plenty of clean power...

Item # 575P300X1

Ships from distributor

In stock
C$349.99

About the Rockford Fosgate Punch P300X1

Big power for your sub or speaker system

Rockford Fosgate's Punch P300X1 mono amplifier produces up to 300 watts RMS, giving you plenty of clean power for your rhythm track. With frequency response from 20 to 20,000 Hz, this full-range amp can also power a center channel or component speaker. You can use the low-pass filter to tune the sizzle away from your sub, or the high-pass filter to keep the lows out of a component speaker. The Punch EQ2 gives you a variable bass and treble boost, in case you want to add a little of that boom and sizzle back into the mix.

Big power for your sub or speaker system

Rockford Fosgate's Punch P300X1 mono amplifier produces up to 300 watts RMS, giving you plenty of clean power for your rhythm track. With frequency response from 20 to 20,000 Hz, this full-range amp can also power a center channel or component speaker. You can use the low-pass filter to tune the sizzle away from your sub, or the high-pass filter to keep the lows out of a component speaker. The Punch EQ2 gives you a variable bass and treble boost, in case you want to add a little of that boom and sizzle back into the mix.

Easy to set for optimum performance

P300X2 control panel shown as example

P300X2 control panel shown as example

Once again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: play the setup tone on the included test CD, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier is now set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Punch amp. At quiet listening levels, you'll hear less background noise and more of your music.

Keeps an eye on things while playing

If that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything.

Maintaining coolness raises efficiency and lowers distortion

Rockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better.

Rockford Fosgate P300X1

                                                    P300X1 connection panel and input clip light

Confused about impedance? Check out our article on matching subs and amps.

READ LESS

Product highlights:

  • full-range mono amplifier
  • frequency response: 20-20,000 Hz
  • 200 watts RMS x 1 at 4 ohms (300 watts RMS x 1 at 2 ohms)
  • CEA-2006 compliant
Features:
  • variable high- and low-pass filter filter (50-250 Hz, 12 dB/octave)
  • variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz)
  • C.L.E.A.N. gain setup system includes test tone CD
  • test tones also available as MP3 download from Amazon On Demand, Rhapsody, Google Play, and Spotify, labeled "3sixty.3 setup disc" (Punch amps and the 3sixty.3 use the same test tone tracks for setup)
  • Class-AB amplifier design
  • Dynamic Thermal Management and MEHSA MOSFET cooling systems
  • MOSFET power and output stages
  • preamp inputs and outputs
  • speaker-level inputs (speaker wire to RCA adapter required)
  • signal-sensing turn-on with speaker-level inputs eliminate need for remote turn-on lead
More Info:
  • optional PLC2 wired remote level control with clip light available
  • 8-gauge power and ground leads and an 50-amp fuse recommended — wiring and hardware not included with amplifier
  • no onboard fuses — when installing multiple amps in a system, an additional 50-amp in-line fuse between the distribution block and the amplifier is recommended
  • 9-15/16"W x 2-7/16"H x 7-13/16"D
  • warranty: 1 year
  • Our 60-day money-back guarantee
  • MFR # P300X1

What's in the box:

  • Mono full-range amplifier
  • Four 1-3/8" Self-tapping screws
  • 2.5mm Allen wrench
  • Quick setup instructions
  • Certificate of Performance
  • Setup/Manual disc

Customer reviews

Loading reviews...

Rockford Fosgate Punch P300X1 reviews

Average review:

24 reviews

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

More details on the Rockford Fosgate Punch P300X1

Mark G.

Product Research

Features
Controls
Connections

Features

CEA-2006 Compliant: CEA-2006 is a system of testing and measurement methods for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring power uses a DC input voltage of 14.4 volts and the RMS power output is measured with 1% or less Total Harmonic Distortion plus noise (THD+N) over a frequency range of 20 Hz to 20 kHz (for full range amplifiers). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4Ω. CEA-2006 allows consumers to compare car amplifiers and receivers on an equal basis. Using CEA-2006 criteria, the Rockford Fosgate P300X1 is rated as follows:

  • Power Output:
    • 4Ω: 200 watts x 1-channel
    • 2Ω: 300 watts x 1-channel
  • Signal to Noise Ratio: 85 dBA (105 dB at rated power)

Cast Aluminum Heatsink: The cast aluminum heatsink dissipates heat generated by the amplifier's circuitry. The inherent advantage of casting provides a 30% cooling improvement over conventional extrusion heatsink designs.

Dynamic Thermal Management (DTM): DTM evenly distributes excess heat across the amplifier's entire heatsink.

MEHSA³ (Maximum Efficiency Heat Sink Application-3rd Generation): MEHSA is a Rockford Fosgate proprietary process that increases the heat transfer from the MOSFET devices to the heatsink. The multi-layer insulated metal MEHSA substrate operates with minimal thermal resistance, spreading heat both downward and outward to quickly dissipate heat from each device across the heatsink. This allows greater power output, enhanced thermal stability, and maximum reliability.

Trans-ANA (TRANSconductance Active Nodal Amplifier): Trans-ANA is a circuit that allows the audio signal to pass through the amplifier at low voltage. The signal is directly level-shifted to the fixed high voltage rails via a pair of drive transistors. Signal linearity is assured by an active node formed by the drive transistors at ultrasonic frequencies. The result is crystal clear sound quality.

NOMAD (NOn-Multiplying Advanced Decision): NOMAD is an intelligent protection circuit that uses an analog computer to make real time decisions regarding temperature, voltage, current and impedance. The amplifier is protected without limiting sound output unless needed.

DSM (Discrete Surface Mount): High speed robotics are used in the manufacturing process to place 1% tolerance parts and large board traces. DSM improves the efficiency of the circuit, decreases cross-talk from other discrete components and lowers operating temperature.

CLEAN Set-Up: Rockford's integrated level setting technology, CLEAN (Calibrated Level Eliminates Audible Noise), replaces sophisticated test equipment with input/output clip LEDs, allowing you to match the source unit's output to the amp's gain, and optimize the amp's output. The input clip indicator works in conjunction with the audio source volume, illuminating red when the source reaches it's clipping point. The output clip indicator works in conjunction with the input level dial on the amp, illuminating the appropriate color depending on the audio content used for the setup.

Power and Protection LEDs: The LEDs are located on top of the amplifier. A blue Power LED illuminates when the amplifier is turned on. A red Thermal LED illuminates if the amplifier overheats. The yellow Protect LED illuminates if a short circuit or too low an impedance is detected at the speaker connections. When any of the protection circuits engage, the amp automatically shuts down until the problem is corrected.

Balanced Differential Inputs: Differential inputs eliminate noise picked up by signal cables by measuring the voltage of both the (+) and (-) input signal, then subtracting the voltage common to both conductors (noise), resulting in only the clean signal entering the amplifier.

Controls

Input Level: To accommodate the varying range of signal levels from today's factory and aftermarket radios, the input level is adjustable from 150mV to 12V.

Crossover: The amplifier's internal crossover has a 12 dB/octave slope. It can be set to high-pass, all-pass (full range), or low-pass operation and the crossover point is variable from 50 Hz to 250 Hz.

Punch EQ: Punch EQ works along with the crossover switch. When the crossover is set to low-pass, the Punch EQ acts as a variable bass boost; 0-18 dB at 45 Hz. When the crossover is set to high-pass, the Punch EQ acts as variable treble boost, 0-14 dB at 12.5 kHz. When the crossover is set to all-pass, both the bass and treble boost circuits are active.

Connections

Power Connections: The power and ground terminals are nickel-plated captive c-clamp wire connectors and will accommodate up to 4-gauge wire. An external 50-amp fuse (not included) must be installed on the power wire. The remote turn-on terminal will accept up to 12-gauge wire. A Phillips or flat-head screwdriver (not supplied) is required to tighten/loosen the terminals.

Speaker Connections: The two speaker outputs are internally wired in parallel, making it easy to connect two subwoofers. The speaker terminals are also nickel-plated captive c-clamps and will accept up to 8-gauge wire. A Phillips or flat-head screwdriver (not supplied) is required to tighten/loosen the terminals.

Signal Input: The RCA inputs will accept either a line-level or speaker-level input. A speaker-level signal can be connected using a Speaker Wire to RCA adapter (sold separately). When using a speaker-level input signal, the auto turn-on feature is active and the remote turn-on terminal becomes a 12 volt output to turn on/off up to two additional amplifiers or other components.

Line Level Output: The amplifier has a pair of RCA line level pass-thru outputs to feed another amplifier. The pass-thru output is passive (the same signal present at the amp's input) and the amp's crossover has no effect on the signal.

Punch Level Control (PLC): An RJ-45 jack is provided for connecting an optional wired remote PLC2 (item number 575PLC2, sold separately), allowing remote control of the output level of the amplifier. A second RJ-45 jack is the PLC output, used to daisy-chain additional amplifiers controlled by a single remote.

Note: Previous model PEQ, Punch Bass, and Para-Punch remotes will not work with this amp.

Loading accessories...

Customer Q&A

Q
Crutchfield asked: Why did you buy this?
A
This will power my sub for bass nicely. [ Clinton  Jul 21, 2018 ]
A
best match for my set up [ David  Jun 21, 2018 ]
A
Need it for a subwoofer install in my 2005 Nissan Frontier SE Crew Cab. [ Seth  May 09, 2018 ]
A
It was in the range I needed for a single 12. I have a '14 Civic coupe, so space is a premium, and a single 12 will do just fine. I like the CLEAR tech, and it's in the right power range for the sub I got with this order. [ Anthony  Jan 26, 2018 ]
A
Needed to add subs to jeep wrangler [ Larry  Dec 19, 2017 ]
A
Safe for my setup [ Chris  Sep 07, 2017 ]
A
Well built unit and great quality as always from RF! [ JERRY  Jan 05, 2017 ]
A
The features, brand name and power is why I chose this car amp. [ Ruben  Aug 12, 2016 ]
A
output power of the amp and the clean technology [ Zachary  Jan 13, 2016 ]
SHOW MORESHOW LESS

5 questions already asked

Q
So, by just using the speaker level input instead of an LOC, I wont need to run a remote wire?
[ David  Dec 29, 2018 ]
2 answers
A
That is correct! If you use a speaker-level input signal, the auto turn-on feature is active which will turn on this amp without needing a remote turn-on wire connected to it. My Bio: https://www.crutchfield.com/bio/Paul
[ Paul  Jan 06, 2019 ]  Staff
A
I ran a remote wire through my ride, it's up to you honestly.
[ Antonee  Jan 02, 2019 ]
Q
So, by just using the speaker level input instead of an LOC, I wont need to run a remote wire?
[ David  Dec 29, 2018 ]
2 answers
A
According to Rockford Fosgate it's not necessary but I ran the line anyway for peace of mind. The wire is small enough to tuck into panels and run without any headaches. But either way, I'm sure you will be happy.
[ Lawrence J.  Dec 30, 2018 ]
A
I run three of these. I was confused here also. I called tech support. I run a second positive 12 volt wire to the remote input. and phono jacks for the audio inputs. works well. I am not using them in a car. I suspect the remote in a car may come from the ignition switch. That way car turns on amp turns on.with out running high current thru ignition wires. Im not a car guy. You could try an audio input to remote it only looks for electricity to trigger.But what is happening to that audio? don't short the amp output. CALL SUPPORT.
[ stephen  Dec 30, 2018 ]
Q
How would this work for an 8" midrange speaker for mid bass purposes???
[ Alex  Aug 10, 2017 ]
1 answer
A
Hello, I currently have mine powering 2-8" subs and it works good. Hard hitting bass.
[ MARK  Aug 10, 2017 ]
Q
I am curious about temperature of unit in use. I have a Rockford P300-1 and it never feels more than warm, even in the summer. It looks to be very similar to this amp except it is not class D like the P300-1 is. It is class AB. I don't expect an audible difference being used for sub woofer. Does it run hot under normal conditions and used properly? I have used AB amps in past and always seemed to be hot when used and worked hard for normal sub use and heat is never good for electronics. Not too efficient if it converts energy to heat so readily. Have they changed? Maybe play it safe and go class D here?
[ Ryan  Feb 21, 2015 ]
3 answers
A
I have one driving a 300 watt sub. I've never had a problem, but I've only had it a few months. One good thing is here is a thermal protection circuit in this unit. If it gets too hot, it shuts down. Good luck.
[ Charles  Feb 23, 2015 ]
A
It's a very dependable amp it always runs cool under pressure from hard pounding subs. It has a light on it that will let you know if it is close to overload or distortion protection . Plus if you get the bass knob for this model it too has a light that does the same thing so you can have your amp in your trunk or out of sight and monitor your bass knob in stead because they work in sink of one another. I hope you choose this amp you will love it too.
[ David  Feb 23, 2015 ]
A
It does get pretty warm... after installing this AB unit- it actually fried a couple days later. Go with the class D. My much older RF amps still push fine and this "new" one is a paper weight now. Not impressed and do not recommend purchasing this amp.
[ Anthony  Feb 23, 2015 ]
Q
WHATS THE BEST 12" SUB TO MATCH WITH THIS AMP FOR MY RAM 1500? POSSIBLY A SHALLOW
[ JESSE  Feb 04, 2015 ]
1 answer
A
Thanks for your question. For information on selecting the best sub for your amp I would recommend reaching out to an Advisor by phone (1-800-324-9695) or online chat. They will be able to help determine the differences between the sub models and help you make the best choice for your system.
[ Krissy  Feb 05, 2015 ]  Staff
SHOW MORESHOW LESS

Loading articles...

TOP