Chat
Contact us
Close contact box
Connect ID #
577 385 43
Connect ID #
577 385 43
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

Our contact center is currently closed.

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-888-292-2575

Thank you, !
Our conversation will be emailed to
Please enter a question  
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  

Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Rockford Fosgate PLC2

Remote control for 2013-up Punch and Power Series amplifiers with C.L.E.A.N. setup system

Item # 575PLC2

Rockford Fosgate's PLC2 wired remote allows you to control the volume of your Punch amp that's equipped with the...

Rockford Fosgate's PLC2 wired remote allows you to control the volume of your Punch amp that's equipped with the...

Top seller

Item # 575PLC2

In stock
C$39.99

About the Rockford Fosgate PLC2

Control and monitor your amp's signal from the front seat

Rockford Fosgate's PLC2 wired remote allows you to control the volume of your Punch amp that's equipped with the C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) setup system. From the driver's seat, you'll be able to adjust the amp's output level and monitor its incoming signal for distortion.

Control and monitor your amp's signal from the front seat

Rockford Fosgate's PLC2 wired remote allows you to control the volume of your Punch amp that's equipped with the C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) setup system. From the driver's seat, you'll be able to adjust the amp's output level and monitor its incoming signal for distortion.

After using C.L.E.A.N. technology to set your amp's gain, just keep an eye on the PLC2's light. It'll turn red when the musical source is distorting, warning you to turn the receiver's volume down before your speakers or subwoofer suffer any damage.

READ LESS

Product highlights:

What's in the box:

  • Rockford Fosgate Punch Level Control remote module
  • 18' remote cable with RJ-45 connectors on each end
  • Mounting bracket
  • Two 1/2" Mounting screws
  • LED with attached 8" harness (used when mounting knob without its housing)
  • Additional front panel
  • Flat washer
  • Nut
  • Installation instructions

Customer reviews

Loading reviews...

Rockford Fosgate PLC2 reviews

Average review:

25 reviews

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

More details on the Rockford Fosgate PLC2

Mark G.

Product Research

Features

Overview: The Rockford Fosgate PLC2 is a wired remote level control, compatible with select Punch series amplifiers. Once the gain control on the amp is set, the PLC2 can attenuate (turn down, not increase) the level from that point, up to -20dB.

LED: The PLC2 features a built-in dual purpose LED; it lights up when the amplifier is powered on, and mirrors the Input Clip indicator on the amp when using the CLEAN setup procedure. The unit also includes an external LED, used when mounting the PLC2 unit without its housing.

Installation: The PLC2 includes cables and mounting hardware for installation. The wired remote can be mounted in a variety of ways:

  • Outside Panel Install: the PLC2 module is surface mounted in its housing, using the included mounting bracket and two mounting screws
  • Panel Install with Front Housing: the PLC2 and the front of the housing are removed from the body of the housing, and flush mounted in the dash; rotary knob extends approximately 5/8" from the dash
  • Panel Install without Front Housing: the housing is completely removed and just the rotary knob's shaft is mounted through the dash; in this case the external LED is mounted separately

Loading accessories...

Customer Q&A

5 questions already asked

Q
I no longer have the volume knob that came with my Rockford Fosgate P300 powered subwoofer. Will this work in it's place?
[ Jamie  Aug 07, 2020 ]
1 answer
A
Hi, to my knowledge this Rockford Fosgate knob control works with a vast majority of Amps & powered Subwoofers in the Fosgate line of product. It should plug rite into your port.
[ Phillip  Aug 08, 2020 ]
Q
Is it possible to run 2 P500x1 amps with one Remote control??
[ Jason  Mar 19, 2017 ]
3 answers
A
No one control for each amp. Unless you were to splice the cords together for one control.
[ Zachary  Mar 23, 2017 ]
A
I'm pretty sure you can just connect the two amps together via the PLC outputs
[ caleb young  Mar 22, 2017 ]
A
I Would advise against it, more than likely overload the control.
[ DUANE  Mar 20, 2017 ]
Q
Will this work on the R500X1D amp? It has an RJ-45 port on the back of it so I would assume so, but I'm not sure
[ CJ  May 28, 2016 ]
1 answer
A
I Would imagine so. Mine actually did not work, I believe my cable was bad. I just haven't taken the time to pull the wire back out and send it in for a replacement.
[ JOSHUA C  May 29, 2016 ]
Q
Will this work on the Rockford Fosgate P1000X5 ?
[ Ron  Dec 06, 2014 ]
4 answers
A
I can only repeat what I stated in my review of this product. I installed it with the RF 1000X5 several months ago. For whatever reason it has minimal effect on the output of the amp. If you really focus on the sound while turning the control you can hear a very little raise and lower of the volume min to max. Nothing else. Also, using the PLC-2 to make adjustments (per instructions) resulted in terrible sound and did not work at all with bass adjustment. I went back to the adjustments made by ear. Finally, I would have sent it back for credit but had to punch a hole in the face plate to install and the light is pretty. From my experience I find this piece of equipment useless with the 1000X5.
[ Edward  Dec 08, 2014 ]
A
The newest one out should work .. They want you to buy new products so old style will not work on newer amps ..
[ jimmy  Dec 08, 2014 ]
A
It will work on any of the new series amps . I add's extra hard bass at the spin if the dial when you need to impress or just want to feel more power then normal. I've got the new amp with the light controls on the amp it will interface with the light controls so you don't have to look at the amp when pushing too much power for too long. So it won't blow your amp. Cost a lot to keep replacing equipment .
[ David  Dec 07, 2014 ]
A
I would assume so, however, I just recently installed it in my truck and am getting no response from the amp. I will be checking with Crutchfield support to see what the problem is.
[ JOSHUA C  Dec 07, 2014 ]
SHOW MORESHOW LESS

Loading articles...

TOP