Contact us
Close contact box
Connect ID #
156 646 03

Our hours

Connect ID #
156 646 03
Chat
All finished with your chat session?

We’ll email you a transcript of this conversation for your records.

For simple questions about your order,
try our new virtual agent:

Please enter your name.  
Please enter a valid email address. Why is this required?
Please enter your US phone number.  

For Tech Support, call 1-888-292-2575

Thank you, !
Our conversation will be emailed to
Please enter a question  
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  

Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Rockford Fosgate R2-500X1

Prime Series mono subwoofer amplifier — 500 watts RMS x 1 at 2 ohms

Item # 575R2500X1

Rockford Fosgate's Prime Series R2-500X1 amplifier can power your subwoofer with up to 500 watts RMS.

Find what Fits your car

Rockford Fosgate's Prime Series R2-500X1 amplifier can power your subwoofer with up to 500 watts RMS.

Top seller

Item # 575R2500X1

In stock
C$369.99

About the Rockford Fosgate R2-500X1

Give your sub the power it deserves

Rockford Fosgate's Prime Series R2-500X1 amplifier can power your subwoofer with up to 500 watts RMS. You can adjust the low-pass filter, infrasonic filter, and Rockford Fosgate's famous Punch boost to get the best possible bass from the sub and enclosure in your vehicle.

Give your sub the power it deserves

Rockford Fosgate's Prime Series R2-500X1 amplifier can power your subwoofer with up to 500 watts RMS. You can adjust the low-pass filter, infrasonic filter, and Rockford Fosgate's famous Punch boost to get the best possible bass from the sub and enclosure in your vehicle.

Setting it up for optimum performance

Rockford Fosgate's C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) setup system ensures your bass will sound as clean and powerful as possible. It's a simple system to use — turn it up until the light shows red, then turn it down until the red light goes out. Speaker-level inputs let you hook this amp up to almost any system, even a factory stereo.

READ LESS

Product highlights:

  • mono subwoofer amplifier
    • 300 watts RMS x 1 at 4 ohms
    • 500 watts RMS x 1 at 2 ohms
  • CTA-2006 compliant
  • Class-D amplifier design
  • variable low-pass filter (50-250 Hz, 12 dB/octave)
  • variable bass boost (0-18 dB at 45 Hz)
  • variable subsonic filter (15-40 Hz, 12 dB/octave)
More Info:
  • C.L.E.A.N. gain setup system includes clip lights
  • wired remote Punch Level Control included
  • auto remote turn-on
  • preamp and speaker-level inputs
  • preamp outputs
  • wiring, fuse, and hardware not included with amplifier
    • 4-gauge power and ground leads and an 80-amp fuse recommended
  • dimensions: 8-1/2"W x 2"H x 7-3/4"D
  • warranty: 1 year
  • Our 60-day money-back guarantee
  • MFR # R2-500X1

What's in the box:

  • Mono subwoofer amplifier
  • Wired Remote Level Control module
  • 16' Remote cable (RJ-25 connector on both ends)
  • One 7" Speaker input harnesses
  • 3mm Allen Hex key
  • Four 3/4" Screws
  • Two 1/2" Screws
  • 5 Flat washers
  • 1 Nut
  • Installation and Operation instructions (English/ French/ Spanish/ German/ Italian)
  • Certificate of Performance
  • Rockford Fosgate contact information

Customer reviews

Loading reviews...

Rockford Fosgate R2-500X1 reviews

Average review:

15 reviews

Filter by rating

Customer photos

Sort reviews

Sort by:
Items per page:
View page:

Verified customer (What's this?)
Verified employee purchase (What's this?)

Pros:

Cons:

Crutchfield response

<< >>

Product Research

Features
Controls
Connections

Features

CEA-2006 Compliant: CEA-2006 is a system of testing and measurement for mobile audio amplifiers. This voluntary standard advocates a uniform method for measuring an amplifier's RMS power output and signal-to-noise ratio. The criteria for measuring amplifier power uses a DC input voltage of 14.4 volts and the RMS power output is measured over a frequency range of 20 Hz to 20 kHz (for full range amplifiers), with 1% or less Total Harmonic Distortion plus noise (THD+N). Signal-to-Noise ratio is measured in weighted absolute decibels (dBA) at a reference of 1 watt into 4 ohms. CEA-2006 standards allow consumers to compare car amplifiers and receivers under the same conditions (apples to apples).

CEA-2006 Specifications:

  • Power Output: 300 watts RMS x 1 into 4Ω
  • Signal to Noise Ratio: >75 dBA (measured at 1 watt into 4Ω)

Other Specifications:

  • Power Output: 500 watts RMS x 1 into 2Ω (14.4 volts)

Mounting: The amplifier can be mounted vertically, horizontally, or inverted using the supplied mounting screws; horizontal mounting (right side up) will provide the best cooling.

Controls

Gain: The rotary gain control is labeled 0 to 11, equivalent to 150mV-4V line level or 450mV-12V speaker level.

Infra-Sonic: The variable infrasonic filter (15-40 Hz, 12 dB/octave slope) is designed to prevent frequencies below the capability of the subwoofer from being amplified. This helps reduce distortion, and is particularly useful when powering subs in ported enclosures.

Frequency: The 12dB/octave low-pass crossover is always engaged (it cannot be bypassed). The crossover frequency is set with a rotary dial, continuously variable from 50-250 Hz.

Punch EQ: The Punch EQ bass boost circuit is adjustable from 0 (min) to +18 dB (max) and centered at 45 Hz.

Auto Turn-on Switch: When using speaker level inputs, this switch can be set to On and the amp will turn on when it senses an input signal (DC offset on the left input). When using the RCA inputs a remote turn-on wire must be connected.

Remote Level Control: A wired Remote Level Control is included, allowing you to remotely control the output level of the amplifier from the dash or center console. The remote has a rotary dial, and comes with mounting hardware and a 16' cable.

Remote Dimensions:

  • Width: 1.16" (2" including the mounting flanges)
  • Height: 0.92"
  • Depth: 1.55" (2.375" including knob and wiring)

Connections

Power Terminals: The power and ground set-screw terminals will accommodate up to 4-gauge wire. The set screws are tightened/loosened with the included 3mm hex key.

Fuse: The amplifier does not have an on-board fuse. An 80-amp fuse should be placed on the power wire within 18" of the battery.

Remote Turn-On Terminal: The remote turn-on set-screw terminal will accommodate up to 8-gauge wire. The set screw is tightened/loosened with the included 3mm hex key.

Speaker Terminals: The set-screw speaker terminals will accommodate up to 8-gauge wire. The set screws are tightened/loosened with the included 3mm hex key.

RCA Input: There is one pair of RCA input jacks. The balanced differential inputs are nickel-plated to resist signal degradation caused by corrosion.

RCA Pass-Thru: A pair of nickel-plated RCA pass-thru jacks provides a convenient way to connect an additional amplifier without running an extra set of RCA cables from the front of the vehicle to the amplifier location. The signal from the inputs is passed directly to the RCA outputs.

Speaker Level Inputs: There is a port for the included speaker input harness. If speaker level inputs are used, nothing should be connected to the RCA jacks.

Loading accessories...

Customer Q&A

Q
Crutchfield asked: Why did you buy this?
A
This pairs great with a sundown audio SD-10 D4, Rockford Fosgate is known for making amps that achieve rated power plus power to spare which complements the Sundown sub which is rated very conservatively to start with. [ Kazz71  May 27, 2020 ]
A
The reputation of the name. [ John  May 26, 2020 ]

3 questions already asked

Q
How do I wire this to output at 2ohm on a single sub? 4 ohm dvc wired in parallel?
[ Matthew  May 24, 2020 ]
2 answers
A
If you have a 4 ohm sub you cant. The DVC is already set up to run at 4 ohms when both are used. Using only 1 VC will result in an 8 ohm (or really close to 8ohm) set up. I have (2) 2 ohm subs bridged across this amp. The set up is close to 1 ohm and the amp is stable and strong.
[ John  Jun 04, 2020 ]
A
This amp has provisions to hook up two speakers. Being a mono amp, both positives terminals are the same connection. Both negative terminals are the same connection, so all you have to do is hook one of the voice coils to one set of positive and negative terminals and the other voice coil to the other set of positive and negative terminals. This will give you your two ohm load. You could also wire the voice coils in parallel and hook them up to one set of the positive and negative speaker terminals. The result is the same.
[ Keith  Jun 04, 2020 ]
Q
Does this require signal processor, or will high input work?
[ Robert  Apr 27, 2020 ]
5 answers
A
High input will work
[ Ellerick  Apr 28, 2020 ]
A
I ran the speaker wires from my factory head unit to the high level inputs. No line out converter or additional processor needed.
[ Keith  Apr 28, 2020 ]
A
Yes this amp has both high and low level inputs. You need remote wire with low level inputs though.
[ JEFF  Apr 28, 2020 ]
A
Hi input will work.
[ John  Apr 28, 2020 ]
A
I'm using the night input on the amp and it's working just fine.
[ Jeremy  Apr 28, 2020 ]

Loading articles...

TOP