Skip Navigation

2008-2017 Mitsubishi Lancer

2008 • 2009 • 2010 • 2011 • 2012 • 2013 • 2014 • 2015 • 2016 • 2017

mitsubishi lancer sedan

In a nutshell: This article is an overview of your Lancer's audio system and its upgrade options. Use our vehicle selector to find the gear that will fit your car. 

Overview of the Mitsubishi Lancer

The final generation of the Mitsubishi Lancer (For now, at least, but who knows?) offers everyday practicality with available all-wheel-drive traction and some upper-level performance models that pack plenty of four-season punch. For some, the best part of a Lancer is the performance and style, while others appreciate the fact that they don't see themselves coming and going on the road every day. Not everybody wants a Toyota or a Honda, and people who want Mitsubishis know exactly what they want and why.

Whether you're driving a rally-inspired Evo or Ralliart, or one of the more sedate models, the Lancer can be a very rewarding vehicle to drive, tune, and enjoy. This edition stuck around for quite a while, and while Mitsubishi kept it up to date with periodic tweaks and improvements, the stock stereos could use some upgrading. We'll hit the high points for both the Sedan and the Sportback.

mitsubishi lancer radio

The radios changed a bit over the years, but the replacement process remained uncomplicated (Crutchfield Research Photo)

Factory stereo system

The factory systems range from the base model all the way up to the (until 2013, anyway) Rockford Fosgate system with a color touchscreen. A late interior update changed the mechanics of replacing the stereo, but single-DIN (2" tall) or double-DIN (4" tall) aftermarket receivers will fit in any of these Lancers.

In non-Rockford cars, if the factory wiring harness does not have an accessory power wire, you'll need to connect your new stereo's accessory power wire to a 12V accessory source in the vehicle. You'll also need to ground the new stereo's ground wire to the chassis of the vehicle.

If your 2008-2013 Lancer does have the Rockford Fosgate system (look for the amp under the driver's seat), note that the factory system requires a low-level signal from the stereo. Thus, the wiring harness will only work with aftermarket receivers that have preamp outputs. Keep that in mind when you're choosing your new stereo. 

Detailed installation instructions

MasterSheet image
If you're looking for step-by-step instructions on how to install a car stereo or speakers in your car, there's nothing better than our exclusive Crutchfield MasterSheet™. This detailed, well-illustrated document is free with your Crutchfield order, or you can purchase one separately for $9.99.

Of course, when you replace any of the stock radios, you'll lose (if you have them to begin with) features like AUX and USB inputs, satellite radio, and navigation. Fear not, because all of those things can easily be regained when you choose the right aftermarket receiver.

The mounting kit and wiring harness adapter you need for your new receiver will be included at a deep discount with your Crutchfield stereo purchase. You'll also get our Crutchfield MasterSheet installation instructions (a $10 value), plus lifetime tech support for the life of your gear (potentially priceless).

mitsubishi lancer radio

Our Crutchfield MasterSheet will show you exactly how to remove the factory radio (Crutchfield Research Photo)

Replacing your factory radio

Installing a new receiver in your Lancer isn't hard, but there are some differences between the 2008-13 models and the 2014-17 cars.

Replacing the radio in 2008-2013 Lancers

You'll start by opening the glovebox, prying out the trim with a panel tool, and removing one Phillips screw. Next, starting on driver's side, pry out on the dash trim strip to release the retaining clips and remove the strip.

Pull up on the bottom of the radio faceplate to release the lower clips, then carefully pull the top of the faceplate towards the rear of vehicle to release the upper clips. Protect the faceplate with a clean cloth or shop rag and just let it hang by harness while you remove the four Phillips screws securing the radio chassis to the dash. Disconnect the harnesses, remove the old radio, and start preparing your new receiver using the instructions for the dash kit and wiring harness adapter.

Tools needed: Phillips screwdriver, panel tool

Replacing the radio in 2014-2017 Lancers

On the later cars, you start by opening the glove box door and removing one exposed Phillips screw on the passenger's side of the box opening. Pry out the glove box side trim panel to release two clips, then remove the panel and remove the exposed Phillips screw.

Next, pry out the dash trim strip to release the retaining clips and remove the strip, then remove the three Phillips screws securing the hazard switch panel to the dash. Pry out switch panel and let it hang while you pry out the receiver trim panel to release ten clips. Remove the panel, then remove the four Phillips screws securing the receiver, disconnect the harnesses, and remove the radio. From here, you're ready to install the new receiver.

Tools needed: Panel tool, Phillips screwdriver

Steering wheel audio controls

It's relatively easy to retain the steering wheel audio controls when you install a new stereo in your Lancer. When you enter your vehicle information, our database will choose the adapter you need to make your factory steering wheel controls work with your new receiver.

Shop for car stereos that fit your Mitsubishi Lancer

mitsubishi lancer door speaker removal

Removing and replacing the front and rear speakers is a great way to upgrade your sound (Crutchfield Research Photo)

Replacing your factory speakers

Whether you have the base 6-speaker system or the Rockford Fosgate system and its added sub, the speakers are reasonably easy to reach and replace.

mitsubishi lancer tweeter

You'll need speaker connectors and backstraps to install new tweeters, but it's not that hard to do (Crutchfield Research Photo)

Removing your Lancer's front door tweeters

The front door tweeters, which are wired in parallel with the woofers, are just a tick over 1-1/2" in diameter. If you're installing a set of component speakers in your Lancer, most aftermarket tweeters should fit just fine. That said, "Measure twice, order once," as they say.

The removal and replacement process is very simple. Just pry out the sail panel to release the retaining clips, disconnect the harness, and remove the grille. Then, remove the two Phillips screws that secure the tweeter to the back of the sail panel.

A speaker wiring harness adapter is not available for these speakers, so you'll want to use Posi-Products speaker connectors to connect them to the factory wiring. And you'll also need our universal backstraps (or hot glue or silicone) to secure them to the sail panel.

Tools needed: Panel tool, Phillips screwdriver

mitsubishi lancer front door speaker

The front door speakers are connected to the doors with keyhole slots (Crutchfield Research Photo)

Removing your Lancer's front door woofers

The 6-3/4" woofers can be replaced by same-size or 5-1/4" or 6-1/2" aftermarket models. You'll have to remove the door panels to do this, but that's not an especially difficult task. Illustrated step-by-step details can be found in your Crutchfield MasterSheet, of course.

If you're replacing the tweeters, which you probably are, the sail panels are already out of the way, so you're a step into this process already. For the woofers, your next task is to pry off the screw cover behind the door release handle and remove one Phillips screw. Pry open the screw cover behind the door pull handle and remove one Phillips screw from that location.

Moving on, you'll pry open the screw cover on the rear edge of the door panel and remove one Phillips screw. Then pry all around the sides of the door panel to release the retaining clips, disconnect the harnesses and cables, and remove the panel. Be sure to store it in a clean, safe place while you continue to work.

The factory speakers are attached to the doors with keyhole slots. To remove each speaker, rotate it counter-clockwise, disconnect the harness, and remove it.  

The speaker harness adapters and, if needed, mounting brackets, are included at a deep discount with your Crutchfield speaker purchase. In the case of some smaller aftermarket speakers, you'll need to drill new mounting screw holes. This isn't hard to do, but any time you're using a drill, it's important to know what's around and behind the area you're drilling into. Work carefully, of course, and always wear eye protection.

Tools needed: Panel tool, small flat blade screwdriver, Phillips screwdriver

mitsubishi lancer rear door speaker

Pretty much everything you do on the front doors will work on the back doors, too (Crutchfield Research Photo)

Removing your Lancer's rear door speakers

In terms of speaker sizes and installation details, replacing the rear door speakers is remarkably similar to what need to be done on the front doors. So similar, in fact, that we're going to save you (Okay, mostly us…) some time and roll right on past this job.

All the important details will be in your MasterSheet, which is included free with your Crutchfield speaker purchase. And if you run into trouble at any point in your installation, remember that your purchase also includes free tech support for the life of your gear. Got questions? Give us a call!

Tools needed: Panel tool, small flat blade screwdriver, Phillips screwdriver

mitsubishi lancer sportback rockford fosgate subwoofer

Replacing the Rockford Fosgate sub is a bit more challenging in the Sportback, but it's still a good DIY project (Crutchfield Research Photo)

Removing the Rockford Fosgate subwoofer

Lancers equipped with the Rockford Fosgate stereo system will have a 10" subwoofer on the driver's side of the trunk (sedan) or cargo area (Sportback). Depending on the aftermarket sub you're installing, you may need to drill new mounting screw holes, so have a cordless drill handy and note the safety precautions mentioned above.

The work itself isn't all that hard in either body style, but the sedan is a lot easier than the hatchback. The major difference is that the Sportback has a few more panels to remove, so the process can take a bit more time.

There are a lot of great 10" subwoofers that will fit in your Lancer, and all the removal and replacement details can be found in your Crutchfield MasterSheet.

Tools needed (Sedan): Phillips screwdriver, 10mm socket, ratchet and extension, cordless drill (maybe)

Tools needed (Sportback): Panel tool, Phillips screwdriver, small flat blade screwdriver, 10mm socket, ratchet and extension, cordless drill (maybe)

Shop for speakers that fit your Mitsubishi Lancer

mitsubishi lancer sedan trunk

It's not a huge trunk, but you can find some space for a sub box if you want one (Crutchfield Research Photo)

Bass in your Lancer

If your Lancer doesn't have a factory sub, or if you just want to go big on bass, there's some room for a sub box in both body styles. In the sedan, you'll have a 37" W X 16" H x 29"/36" D space to work with. In the Sportback, it's 38" W x 13" H x 25"/32" D. Like we said, there's some room, but not a ton.

If you want to add more bass without sacrificing everyday utility, consider a compact powered subwoofer.

Kicker 43DXA250.4 4-channel amplifier

A 4-channel amp will really bring out the best in your speakers

Other options for your Lancer

Here are some other nifty upgrade ideas for your Lancer.

Add an amp (or two)  

A new 4-channel amplifier will help you get the most out of your new speakers. You'll get cleaner power (and a lot more of it), which will result in much, much better sound. A mono amp can provide the juice you need for your new subwoofer, too.

Check out a camera

The Lancer offers decent visibility, but it's always nice to have some help when you're backing up in a crowded parking lot. We offer a wide variety of backup cameras that will make that a lot easier, plus they'll blend in better than the optional factory model found in later Lancers. You can go for a camera that mounts to your license plate and works with your new aftermarket nav receiver, or choose a system that displays the images in an aftermarket rear view mirror.

If you enjoy taking your Lancer out for spirited drives on your local backroads, a dash cam is a great way to record your most enjoyable excursions. And on the way home, they're very handy for recording the behavior of the less-talented motorists around you.

Put in a car security system

Installing a security system in your Lancer isn't easy (security systems rarely are), but it's definitely a good idea. Our Crutchfield Advisors can help figure out what you need to get the job done, but we usually recommend taking your car and new gear to a professional installer.

Shop for car security systems for your Mitsubishi Lancer

Find the audio gear that fits your car or truck

Visit our Outfit My Car page and enter your vehicle information to see stereos, speakers, subs, and other audio accessories that will work in your vehicle.

Ask an expert advisor

No pressure, no commission — just lots of good advice from our highly trained staff.

Find what fits your vehicle

 
 
 
 

Can't find your exact vehicle?

 
 
 
 

would like to send you to a different page.

Go there