About the PAC HDK001X Dash and Wiring Kit
This PAC HDK001X factory dash and wiring kit allows you to install a single-DIN (2" tall) radio in select 1998-2013 Harley-Davidson models with factory fairings. It includes a pre-programmed interface to retain the factory handlebar audio controls and a pre-wired installation harness that requires no cutting of any factory wires. The kit features two options of frames for the aftermarket radio installation (with or without a hinged tinted/UV protective cover). Warranty: 1 year.
Note: You'll only retain your handlebar audio controls with cars stereos made by Alpine, Clarion, Dual, Kenwood, Jensen, JVC, Pioneer, Sony, or Valour.
What's in the box:
PAC HDK001X Dash and Wiring Kit owner's manual
- Radio housing
- Radio housing w/ splash-guard
- Handlebar control interface module
- Wiring harness
- Rubber gasket (pre-installed)
- 2 Brackets
- 2 Spacers
- 4 Long bolts
- 4 Short bolts
- 4 Hex-nuts
PAC HDK001X Dash and Wiring Kit reviews
This review was collected as part of a promotion
More details on the PAC HDK001X Dash and Wiring Kit
Harley Davidson Radio Replacement Kit: The PAC HDK001K radio replacement kit makes it possible for Harley Davidson motorcycle enthusiasts to integrate an aftermarket radio into their ride. This Harley Davidson radio replacement kit includes a pre-programmed interface to retain the factory handlebar audio controls, installation harness, two options of radio housings for the aftermarket head unit installation, and mounting hardware.
Compatibility: The PAC HDK001X is compatible with select 1998-2013 Harley-Davidson motorcycles and most aftemarket radios with a wired remote input that are steering wheel control ready.
- VehicleThe PAC HDK001X is compatible with select 1998-2013 Harley-Davidson motorcycles (FL models with factory fairings). The PAC HDK001X does not retain rear speakers; these will need to be hard wired.
- Radio: The aftermarket radio must be equipped with a wired remote input (3.5mm headphone style jack or Blue/Yellow wire) to be compatible. Not compatible with Sony XAV series head units; Kenwood KDC-X598, KDC-BT318U, KDCBT-758-HD, KDCBT-558U and KDC-X798 head units, and Alpine UTE-73BT, CDE-172BT, CDE-173BT and CDE-175BT head units.
Radio Housing: The PAC HDK001X comes with two radio mounting kits that will fit most single-DIN aftermarket head units. One of the mounting kits features a hinged tinted/UV protective cover, while the other mounting kit does not.
Retains Handlebar Audio Controls: The included SWI-HD interface module allows you to retain your Harley Davidson's handlebar audio controls. The included SWI-HD interface module is compatible with Alpine, Clarion, Dual, Kenwood, Jensen, JVC, Pioneer, Sony, & Valor aftermarket head unit's that features a SWC input (3.5mm) or SWC wire (Blue/Yellow). The interface comes pre-programmed, but can also be reconfigured.
Wiring Harness: The PAC HDK001X comes with a wiring harness which plugs directly into the included interface module and your Harley Davidson's factory radio plug. You will need to hard-wire the following seven wires of the harness to your new aftermarket head unit's wiring harness.
|Yellow||+12 Volt Constant|
|Red||+12 Volt Accessory|
|White||Left Front Speaker +|
|White/black||Left Front Speaker -|
|Gray||Right Front Speaker +|
|Gray/black||Right Front Speaker -|
Installation Note: Factory CB, intercom, and rear volume control functions are integrated into the Harley Davidson stock radio and cannot be retained when adding an aftermarket radio. Depending on bike configuration it may be necessary to install new rear speaker wires.
10 questions already asked
90% Plug and Play. I uses this to install a Kenwood stereo in my Harley. It was a simple install and plugged into the factory harness. Handlebar controls all work too!!
Daniel from Roebling, NJ