Contact us
Close contact box
Connect ID #
744 876 69
Connect ID #
744 876 69

Sorry, chat is currently unavailable

Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

6 tips for home A/V cable management

Tame your home theatre cable tangles

Cables tied near the end with a wrap.

In a nutshell: Your home theater system should be a source of joy — both for sound and appearance. If yours looks like an explosion in a spaghetti factory, read on.

Most systems have three problem areas:

  • Scraggly wires hanging down from a wall-mounted TV
  • A snarled mass of cables connecting components in the back of an A/V cabinet
  • Loose wires snaking across the room to rear surround speakers

This article is about simple, inexpensive remedies for each of these issues. 

Loose versus bundled cables under a TV.

1. Use wire ties to bundle cables

Have more than one cable running to or from your TV, cable box, or receiver? Bundle them up with ties.

Some wire ties are reusable — like the Methra ethereal Velcro® cable wraps. They're a great option for renters.

Here are four tips for using ties effectively:

Illustrations of how to use cable ties.
  1. After routing and connecting cables, bundle at one end. This makes them easier to handle.
  2. Don’t cinch the ties too tight. They can crimp the wires and damage their insulation.
  3. Snip off any excess from the ties for a clean look.
  4. Bundle A/V cables and power cables separately.

2. Secure your wire bundles

Adhesive pads designed to work with wire ties can be attached to walls. These can help keep rear channel speaker wires out of the way by securing them to your wall’s molding.

These adhesives can also hold a cable bundle running from a wall-mounted TV flat against the wall for a neater appearance. You can also use them to fasten wires and wire bundles to the back of your A/V cabinet.

You can also attach your bundles using cable clamps.

Be sure to match the shape and the size of the clamp to the cable. Use screws rather than tacks to secure these clamps. They're more secure, and you can easily remove and reattach them if you rearrange your cables. 

3. Use raceways to conceal cables

You don’t have to run wires inside walls to conceal them. Raceways are plastic or wooden channels that conceal and protect wires and wire bundles.

Raceways attach easily to walls and baseboards. Most are paintable, so you can make them blend into the background and virtually disappear.

Raceways come in different sizes. If you’re concealing a cable bundle, make sure the raceway is big enough to comfortably fit over it.

Wires running behind a raceway.

4. Label everything

Labeling your wires ensures you can easily identify each of your cables. You'll be able to quickly swap out a component without losing track of what's what.

Crutchfield’s color-coded CableLabels are a great solution. They come pre-printed with all the most commonly used components in an A/V system.

You can also make your own labels. The important thing is to do so — even if your system’s small and relatively simple. As it grows, you’ll be glad your cables were organized from the start.

5. Organize the cables behind your equipment rack

Bundling cables can bring the mass of wires behind a rack or A/V cabinet under control. Wire ties are the best solution here.

Remember to bundle power cables and A/V cables separately. That minimizes the chance that electromagnetic interference from power cables will degrade your system’s performance.

You can also use tacks or adhesive pads to secure bundles to the back of your rack or cabinet.

6. Secure loose wires running to rear surround speakers

Wires running to rear speakers should be secured so you won't step on them or trip over them.

Running wires under carpeting isn’t recommended — especially in high traffic areas. If the wires are continually stepped on, over time their insulation can get rubbed away. It’s best to run rear channel wires along the baseboard.

Wire tacks are the easiest way to secure this wire. Or use raceways for a more finished appearance.

For more helfpul tips, see our home theater receiver setup guide and our in-wall wiring guide.

  • Adina Hirschmann from Bergenfield, NJ

    Posted on 7/5/2023

    I rent my apartment in a building where the landlord does not allow drilling through walls, ceilings or removal of plaster. I had to come up with a solution that would allow enough room for my wires and cables, yet allow flexibility around doorways, under stair treads and on top of baseboards. I used to work in a garment factory and had some long bundling strips made out of a stretchy polyester doubleknit fabric. I folded the strips along the long edges and handsewed them, joining them together, while maintaining the tubular form, encasing the wires and cables as I sewed them. Mounting was accomplished with cup hooks and wire fasteners, poked through the seams to grip around the coaxial cable---the most rigid and strongest in the bundle--- and secured with screws and anchors. When mounted, it resembles an umbilical cord, carrying nourishing signals to and from my speakers and components. I wish there was an option to post photos.

  • Anthony

    Posted on 5/23/2023

    I have a real mass in the back I have just wire going in the back for the speakers I guess I just don't know what I'm doing.

  • Lawrence Brown from New Port Richey

    Posted on 8/22/2022

    I would like an adapter that goes from the round plug in powered subwoofer to an RCA cable do you have an adapter to fit cable

  • Lawrence Brown from New Port Richey

    Posted on 8/22/2022

    I would like an adapter that goes from the round plug in powered subwoofer to an RCA cable do you have an adapter to fit cable

  • Lawrence Brown from New Port Richey

    Posted on 8/22/2022

    I would like an adapter that goes from the round plug in powered subwoofer to an RCA cable do you have an adapter to fit cable

  • Alan from New Auburn

    Posted on 2/9/2021

    Not too much problem going to optical instead of 2 heavy RCA cables and HDMI. But, what to do with all the power cords. Amp, Pre-amp, CD, Blue Ray, DTV box, Roku box, TV 'One-Box" (Samsung), Sound Bar, Panamax power conditioner. Just a mass of cables. Power cords are often way to long for a more compact cabinet. with 2 wide by 3 high shelves. A source for shorter power cords would be nice. By short, I mean 2-3 feet .

  • Tim leitzes from Sunrise ,fl

    Posted on 1/19/2021

    Excellent advice and detailed instructions as only crutchfield would do. I just purchesef the sennheiser5000 from you an excellent price of equipment. No problem with hook up . To my non blue tooth amp. Works just fine thank guys

  • joey ambs from Owensboro

    Posted on 10/9/2020

    Iam wanting to hook-up my sound bar to my tv. I don't have the right connections on the ends of my cord. Waiting to get it right, Thanks for any help on the matter........

  • Brendan Moran from Cambridge

    Posted on 5/14/2020

    Very nice tips. Any recommendations on managing cables from a cabinet to the wall, so the cabinet can be moved for cleaning/access, without the cables being pulled from the units. I know you can leave slack in, but then don't really want it trailing all over the floor either. Any suggestions appreciated.

  • nelson 5076 street from marion 3597 ave

    Posted on 1/31/2020

    madison 2831 ave

Compare the sound