Chat
Contact us
Close contact box
Connect ID #
962 500 79
Connect ID #
962 500 79

Sorry, chat is currently unavailable

Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

Tips for installing tower speakers on a boat

The great sound is worth the effort

In this article, we'll explain how to install a set of wakeboard tower speakers on your boat so that your skiers and boarders can rock out while they're rolling along the waves.

What could make water skiing and wakeboarding more fun? Adding a soundtrack, of course. With the popularity of water skiing and wakeboarding, it’s no wonder that tower speakers are some of the best-selling marine audio products on the market.

The concept behind tower speakers is pretty simple. Powerful woofers and tweeters are stuffed into sealed, conical, weather-resistant enclosures that will be attached to a wake tower and pointed aft. With a set of these speakers on your boat, skiers and boarders can get down to music as they bounce along behind the boat. More music means more fun, so a set of tower speakers will help make your day on the water even more enjoyable.

When you’ve decided that it’s time to add tower speakers to your boat, there are three things you need to take into account: power, mounting, and wiring. Here, then, are the basics along with a smattering of expert tips from us.

Tower speakers need more power

Tower speakers require a lot of power to sound their best. That's because they’re mounted up in the air and basically firing sound into the empty air behind a speeding boat. That leads to rapid sound dispersion, of course, plus there's going to be an engine or two howling along at high revs. With all that going on, the key to getting the sound you want is power — and plenty of it.

The more power you can apply to the speakers, the louder they’ll play and the better they’ll sound. Make sure your boat audio shopping list also includes an external amplifier that has an RMS power rating that's equal to or less than the speakers’ power-handling specs.

To learn more about all that, check out our Marine Amp buying guide.

JL Audio marine amplifier

An outboard marine-rated amp is exactly what you need to get full performance from power-hungry tower speakers.

Mounting the speakers on your tower

The most common way to attach speakers to your boat’s tower is with a set of rust-resistant clamps. You simply place the clamps around the towers and secure them with the included bolts. This allows you to adjust the vertical angle so that it’s just right for your wakeboarders. The clamps then typically allow the speakers to swivel so that you can get the best sound dispersion possible.

Tower speaker clamps

Stainless steel clamps keep tower speakers in place. After choosing the mounting spot, loosely clamp them to the tower before mounting the speakers; it's a little easier that way.

When choosing the exact mounting spot, you’ll want to balance spacing with clearance. Place them wide enough apart to get appealing stereo separation, but make sure they’re in spots that’ll reduce the chances of people on your boat knocking their noggins on the enclosures every time they stand up.

Tightening speaker clamps

Once you have the horizontal spacing and vertical angling established, you're ready to tighten everything up.

Many towers are designed specifically to accommodate speakers. We carry a variety of brackets that match various mounting systems. All you’ll need to do is make sure to match the bolt-hole pattern correctly. If you have any questions, one of our marine audio experts will be happy to help

Run the wiring through the tower

The toughest part of installing tower speakers is connecting them to your amplifier. Specifically, running wires through the legs of your boat’s tower can present something of a challenge. It's nothing that a little planning and patience can’t overcome, but it's not the easiest thing you'll ever do.

Many newer towers come pre-wired for speakers. If that’s the case with yours, you’ll simply need to connect these wires to your new speakers at the top, and to your amplifier, wherever you’ve mounted it.

If your tower isn’t wired for sound, that’s okay. It’ll still have a channel in the crossbars and at least one of the legs, so you can use that to accommodate speaker wire.

In our experience, one convenient way to run wire through your tower is to take advantage of the safety light that’s required on the top of any boat tower. The light will have a wire running from the light, down the tower, and to a switch on your boat’s dash. You can temporarily disconnect the wire from the switch, then tape the speaker wire to the light wire. Then, you can pull the light wire up through the tower, bringing the speaker wire along with it.

Wire threaded through a tower leg

Your tower should have a safety light installed; you can use the light's wire to help pull speaker wire through the tower leg.

Expert tips for running speaker wire:

  • Lubricate the wires so that they slide through the channel more easily.
  • Don’t wrap the tape too thickly around the wires, or they might get caught in the channel.
  • Feed plenty of slack into the tower before you pull from the top; lessening the tension on the wires will make the job easier.
  • Don’t pull too hard or fast; too much strain can cause the light wire to separate from the speaker wire.
  • Pull at least twice as much speaker wire through the tower as you’ll actually need. When that’s done, you can use the extra speaker wire to pull the light wire back down through the tower.
  • Run wires for both speakers at the same time, if possible.

Most towers have holes in the crossbars at the spots where you’ll mount the speakers. You can use a small pick or hook to fish the speaker wire through these holes. In some cases, you’ll need to widen the existing holes or drill new ones. If you don’t already have one, you can typically find special drill bits for use on stainless steel at your local hardware store.

A second method is to thread the speaker wires from the holes in the crossbars down through the legs and into the boat. This can be much trickier, as you’ll have to negotiate the bends and turns in the tower. A roll of fish tape can be a good option for threading the wire. A wire coat hanger, if you can find one long enough, can also be a big help. The thin, pliable nature of a coat hanger can sometimes find its way through a tower’s bends more easily.

When it comes time to splice the wire you’ve run through the tower to the speakers’ wires, we recommend using solder and heatshrink tubing. This type of connection offers the most resistance to water damage or corrosion.

Using a heat gun with heat shrink tubing

Soldering your connections then sealing them with heat shrink tubing and a heat gun will help keep keep corrosion at bay.

When your wires are spliced, push any remaining slack into the crossbar before you secure the clamps. If your mounting location requires the exposure of some of the wire, we strongly recommend covering the wire with loom for both protection and aesthetics.

Expert advice for your tower speaker project

Adding tower speakers brings tons of fun and excitement to any sport boat, and they’ll look fantastic, too. If you’d like a hand sorting through our options or matching them to a suitable amplifier, be sure to contact our Crutchfield Advisors. And once you’ve gotten your new speakers to your dock, you can count on our free, in-house tech support for over-the-phone installation help if you need it.

And if you want to learn more about the hows and whys of installing new gear on your boat, check out our "Pro tips from our marine audio experts" article.

A day on the water is better with music
  • Thomas

    Posted on 6/28/2023

    Once I run my wires down the Tower tubing, how do I get them into my boat and to the radio? I don't ever see anyone showing that step

Find what Fits your vehicle

Remove

Checking fit...

Compare the sound